Filter
Top Products
GB
OWNER’S MANUAL
•
E30
7
If you have set target/targets, the target/targets
start to count down. During training the equipment
will adjust resistance dependently on your pedaling
speed, so that target power level is achieved and
maintained. You can change the target power by
SELECTION DIAL.
6. RECOVERY
Start the recovery calculation after training by
pressing RECOVERY button. Recovey heart rate
calculation can be started only if the heart rate
measurement is activated and the heart rate value
is shown on the display The measurement takes 60
seconds. After 60 seconds, the display shows your
recovery index F1-F6 (F1 = best result). To get back
to main menu, press RECOVERY button once again.
7. BODY FAT
Press BODY FAT button to start measurement. Hold
both hands on the handgrips and wait for 8 seconds.
The meter will show body fat advice symbol, body
fat % and BMI for 30 seconds.
SETTING USER DATA
Right after restarting the meter or reset (long
push) you can enter to the user menu. Select the
user and confirm. Set your sex, age, height and
weight. Confirm by selection dial. Personal exercise
target data (time, distance, energy, heart rate limit)
will be memorized and recalled as defaults every
time when the user is selected. If you modify your
personal training data, it will automatically be
memorized.
ADDITIONAL NOTES
1. For speed and distance you can choose either
metric or English units by using the KM/ML switch
located on the back cover of the meter. The power
cord has to be unplugged and replugged to apply
the change.
2. If you are not training and buttons are not
pressed, the meter switches into the Sleep mode
after about four minutes. Room temperature is
displayed.
3. Training is paused for a maximum of 4 minutes
by pressing the START/STOP button. Pressing the
button again allows you to continue the paused
training session using the previous training data.
4. Entering training targets (time, distance, energy,
heart rate limit) is possible only in the STOP mode
(not during training).
5. If you don’t want to change your user data every
time you start training, press START/STOP to skip
user data editing. You’ll enter to the training in
Manual mode.
6. This equipment cannot be used for therapeutic
purposes.
7. Energy consumption is calculated based on
average values. The energy expenditure is displayed
in kilocalories. To convert this into joules, use the
formula: 1 Kcal = 4.187 KJ.
8. If you are training with heart rate measurement
(either chest belt or handgrip heart rate) you can set
maximum heart rate limit. When limit is exceeded
while training meter will give alarm beeps.
9. Preset programs are divided into 16 steps.
Duration of the one step depends on the time set
for the whole training. If time is not set, duration of
one step will be 100 m in distance.
10. If you have set targets to count down, a signal
sounds and training automatically stops when any
of target reaches zero. You can restart training by
pressing START/STOP
11. Note that recovery index is in relation to the
heart rate frequency in both the beginning and the
end of the measurement.
12. In H.R.C program heart rate target ranges (55%,
75% and 90%) are calculated as percent from your
age predicted maximum heart rate (calculation
formula: maximum heart rate = 220 – age).
13. Automatic adjustment of the resistance during
H.R.C program occurs upwards every 30 seconds
and downwards every 15 seconds, if needed.
14. BODY FAT is a personal measurement and the
result is based on average european population
values.
B.M.I. (Body Mass Index) table:
LOW < 20
LOW / MEDIUM 20 - 24
MEDIUM 24 - 26,5
MEDIUM / HIGH > 26,5
Formula for BMI = weight (kg) / height^2 (m)
BODY FAT % (average european population) table:
Male:
LOW < 13
LOW / MEDIUM 13 - 26
MEDIUM 26 - 30
MEDIUM / HIGH > 30
Female:
LOW < 23
LOW / MEDIUM 23 - 36
MEDIUM 36 - 40
MEDIUM / HIGH > 40
MAINTENANCE
The equipment requires very little maintenance.
Check, however, from time-to-time that all screws
and nuts are tight.