Filter
Top Products
You will then be ready to set the time in the zone you selected.
Press S3 and the SECONDS will be flashing on the display.
Pressing S1 or S2 resets seconds to :00. NOTE: SECONDS can
not be set in T-2; they will automatically be the same as for the
T-1 setting.
Press S3 to change the active (flashing) digits to SECONDS,
HOURS, MINUTES, DAY and YEAR. Press S3 again and the
display will show 12/24 Hr SELECT. Either the 12 or the 24 will
be flashing indicating the active time format. Change it if you wish by
pressing S1 or S2, and then S3 to select the format.
The next press of S3 returns you to SET TIME T-1 (or T-2). You can move
through the rotation of active digits as often as you wish, stopping when
one you wish to change is flashing. You can move in the reverse direction
by pressing S5 instead of S3.
Press S4 to exit from the Set mode. You can do this at any time (you do not
have to set every item). If no button is pushed for 2-3 minutes, the watch
will automatically return to Time/Calendar mode in the time zone that was
active when you entered the Set mode.
=Flashing
SECTION 6 – USING THE CHRONOGRAPH
The chronograph (or stopwatch) is used to measure elapsed time from a
beginning point; for instance, to time a race. It can be used to record
segments of your training routine to evaluate your progress.
Press S5 (once from Time/Calendar mode) until CHRONO
shows in the lower display. In 2 seconds, this will be replaced
by a screen showing LAP 00 in the upper display and SPL 00 in
the lower with the CHR flag showing between them and a
segment number at the bottom (SEG 1 for example).
NOTE: Any mode title (such as CHRONO) that appears in the display can be
immediately erased by pressing S1, S2, S3, or S4.
If the chronograph is already active, you’ll see the running count, or the
last time at which the count was stopped. Press S2 to stop a running
count, press S2 again to store the segment, and S2 once again to clear the
segment.
To Start: Press S3 to start the chronograph. It will count minutes,
seconds, and hundredths for the first 60 minutes, at which time it will
display hours, minutes, and seconds. After 100 hours, the chronograph will
stop and display “100+ Hr.”
If you are taking a single reading, the lap time (upper display) and the split
time (lower display) will be the same; at the bottom will be the legend S-1
L-1 (Segment 1, Lap 1). You can switch back to Time/Calendar mode and
the chronograph will continue in the background. You can peek at the
chronograph from Time/Calendar mode by pressing S1, but you must go
back into to Chrono mode to operate the chronograph.
To Record Lap Times: With the chronograph running, press S3 to record a
lap time. The upper display will show the lap time and the lower display
will freeze temporarily to show the split time. (Note: lap time is for the last
timed lap, split time is the total elapsed time from the start of the segment).
After 10 seconds, your watch will resume showing the current lap and split
times on the display. To resume showing the current time before 10
seconds have passed, press S4 or S5.
SECTION 5 – SETTING THE TIME AND DATE
With the Time/Calendar display showing, press S4. The display
will show HOLD-TO ENTER SET MODE; if you continue to hold
S4 for two more seconds, you will enter the Set mode. The
display will then show SET TIME, and either T-1 or T-2,
depending on which time zone was showing when you pressed
S4. Select which time zone you want to set by pressing S1 or S2.
BASIC OPERATION OF YOUR WATCH
The six buttons (labeled in clockwise order) on the watch perform different
functions depending on the mode being used. In general, for most active
modes, the button functions are:
S1 Peek at Chronograph, Recall Chronograph, or Alarm Select
S2 Peek at Memo, Stop/Store/Clear Chronograph, Arm/Disarm Chime
S3 Peek at or Change to Alternate Time Zone, Start Chronograph, Record
Lap/Split Times, Start Timer, Arm/Disarm Alarm
S4 Enter and Exit Set Mode
S5 Change Modes
S6 INDIGLO night-light, Arm/Disarm Night-Mode
In the various setting modes, the functions are:
S1 Increase the digit being set (this digit will be flashing – holding this
button down will cause the digits to increase rapidly)
S2 Decrease the digit being set (this digit will be flashing – holding this
button down will cause the digits to decrease rapidly)
S3 Select the digit to be set in the forward direction (changes which digit is
flashing)
S4 Exit the Set mode
S5 Select the digit to be set in the reverse direction
S6 INDIGLO night-light
CHANGING MODES
Pressing the S5 button allows you to change modes: from Time/Calendar,
to Chronograph, to Timer, to Alarm and finally to Memo. The next press
returns you to Time/Calendar mode.
NOTE: If you press any other button while in a mode, the next press of the
S5 button will return you to Time/Calendar.
KEEPING TIME IN TWO TIME ZONES
As noted before, your watch maintains the time in any two time zones that
you set. Usually you will select the time where you live as T-1, and a
frequently-needed alternative (your company’s home office, a friend
overseas, etc.) as T-2.
You can “peek” at the time in T-2 by pressing the S3 button. When you
release the button, the display will return to T-1. If you hold the S3 button
for four seconds, the display will show HOLD-TO SELECT. If you continue
pressing the S3 button for two more seconds, the display will change to
show T-2 as the actively displayed time zone. You can then use the S3
button to “peek” at, or change back to, T-1 in the same way.
CORE #70 1/17/97 11:25 AM Page 3