Filter
Top Products
Assembly Instructions
2
For Your Safety
■ Only use the Cross-Trainer for its intended purpose, i.e. for the
physical training of adult persons.
■ Any other use is inadmissible and may be dangerous. The
manufacturer cannot be made liable for damage caused by a
use that does not correspond with the intended purpose.
■ You train with an equipment that has been designed in accor-
dance with the latest state of the art regarding safety. Possible
danger spots that may cause injuries have been avoided and
safeguarded as well as possible.
■ The unit requires a power supply of 110 V/60 Hz. It should be
connected only to a safety socket with a single 10-A fuse. Be-
fore commissioning the appliance pay attention to the fact that
the correct plug-in power supply unit (observe marking) has
been connected properly. Do not under any circumstances car-
ry out electrical repairs or alterations yourself. Always ensure
that such work is done by a properly qualified electrician.
■ Important: disconnect the apparatus from the mains before
doing repair, maintenance or cleaning work.
■ The equipment must be set up on firm even ground. Ensure that
the power cable is not pinched and that no-one can trip over it.
■ Improper repairs and design changes (disassembly of original
parts, installation of inadmissible parts, etc.) may cause haz-
ards for the user. Do not under any circumstances carry out
electrical repairs or alterations yourself. Always ensure that
such work is done by a properly qualified electrician.
■ When the unit is not in use, unplug it from the power
supply.
■ Never allow liquid of any kind to enter the interior of the unit.
■ Defective parts may impair your safety and the service life of
your equipment. Therefore, please exchange defective or worn
parts immediately.
■
Always observe the general safety rules and precautions
for working with electrical equipment.
■ If you have any doubt or any queries, please contact your spe-
cialised dealer.
■ If you train regularly and intensively, please check all equip-
ment parts – in particular bolts and nuts – every 1 to 2 months.
This is particularly true for the attachment of grip strap and run-
ning plate.
■ Inform present persons (especially children) about possible
hazards during your exercises.
■ Prior to taking up training, have your family doctor check
whether your state of health is sufficient to train with this equip-
ment. The medical findings should be the basis for the build-up
or your training program. Wrong or excessive training may
lead to damage to your health.
■ By all means observe the information about the organisation of
training in the training instructions
■ Our products are subject to a constant innovative quality assu-
rance. We reserve the right to perform technical changes re-
sulting therefrom.
Please, thoroughly read these instructions prior to assembly and first use. You will get important information about your
safety as well as the use and maintenance of your Cross-Trainer. Keep these instructions for reference and/or for main-
tenance work or spare parts orders.
Handling the equipment
■ Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.
■ It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust.
■ The Cross-Trainer is designed for use by adults and children
should not be allowed to play with it. Children at play behave
unpredictably and dangerous situations may occur for which
the manufacturer cannot be held liable. If, in spite of this, chil-
dren are allowed to use the equipment, ensure that they are in-
structed in its proper use and supervised accordingly.
■ The Cross-Trainer conforms to the safetyrequest of part H of the
DIN norm EN 957. The Cross-Trainer works independent of
revolutions per minute.
■ On principle, the equipment does not require any special
maintenance. All bearings have a lifetime lubrication or are
maintenance-free.
■ For cleaning and caring by no means use aggressive or cor-
roding agents but environmentally beneficial ones.
■ The Cross-Trainer possesses a magnetic brake system which is
maintenance-free and does not require any adjustment.
■ Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
Instructions for Assembly
■ Ensure that you have received all the parts required ( see check
list ) and that they are undamaged. Should you have any cause
for complaint, please contact your Kettler dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person.
■ The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as in-
structed. The required tools are supplied with the equipment.
■ Bolt all the parts together loosly at first. Do not tighten any of
the bolts until the assembly operation has been fully completed.
■ Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
■ For technical reasons, we reserve the right to carry out prelim-
inary assembly work (e.g. addition of tubing plugs).
List of spare parts
When ordering spare parts, always state the full article number,
spare-part number, the quantity required and the inspection num-
ber stamped on the back.
Example order: Art. no. 7858-699/spare-part no. 70122771/2
pieces/inspection no. ....................
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words „with
fastening material“.
USA