Filter
Top Products
4
DOUBLE REPEAT TIMER (for Cal. S057)
● Two timers are available for use either individually or in combination. When used together, Timer 2 starts counting down as soon as Timer 1 has finished
counting down the set time. They repeat their respective countdown cycles alternately as many times as necessary unless stopped.
● Each Timer 1 and Timer 2 can be set for any desired amount of time from 10 seconds up to 99 hours, 59 minutes and 59 seconds in one-second increments.
● To use either Timer 1 or Timer 2 as a standard repeat timer, set the timer not in use to “00:00’00.”
● The number of times that the timers repeat their countdown cycles can be set from 1 to 100 times. If “---“ is set for the number of repeating times, the timers
will automatically start over a new counting until stopped by the user.
A
Number of times
the countdown is
to be repeated
B
D
Timer 1
Timer 2
Number of times
the countdown
was repeated
TIMER SETTING
Press to show the TIMER display.
▼
D
B
Press and hold for 2 seconds to show the TIMER SETTING display.
▼
C
Press repeatedly to select the digits (flashing) to be adjusted.
* The HOUR digits for Timer 1 start flashing.
▼
A
Press to set the flashing digits.
* The digits move quickly if Button A is kept pressed.
* By pressing Button D while the digits are flashing, both of the timers and the number of times the
countdown is to be repeated will be reset to “00:00'00"” and “000,” respectively.
B
▼
After all the adjustments are completed, press to return to the TIMER display.
C
HOUR
(TIMER 1)
MINUTES
(TIMER 1)
SECONDS
(TIMER 1)
HOUR
(TIMER 2)
MINUTES
(TIMER 2)
SECONDS
(TIMER 2)
NUMBER OF TIMES THE
COUNTDOWN IS TO BE REPEATED
●
The timers cannot be set for a time less than 10 seconds. If a time less than 10 seconds is set and Button B is pressed to return to the TIMER display, the timers
will automatically be set to “00:00'10".”
How to use the timer
●
To stop the time-up warning beep and time-up beep while sounding, press either Button A, B, C or D. This will not affect the time-up beeps for the subsequent
countdown cycles.
●
The time-up beeps of Timer 1 and Timer 2 sound in different tones.
●
Restarting and stopping the timer can be repeated as many times as necessary by pressing Button C.
Press Button C to start
Timer 1.
C
mark flashes during
the countdown.
A time-up warning beep
for Timer 1 sounds 3
seconds before the set
time is up. When the set
time is up, time-up beep
for Timer 1 sounds for 5
seconds.
TIMER 2 starts
counting down.
A time-up warning beep
for Timer 2 sounds 3
seconds before the set
time is up. When the set
time is up, time-up beep
for Timer 2 sounds for 5
seconds.
TIMER 1 starts counting
down.
In this way, both the timers repeat the countdown the number of times you have set,
showing the number of times the countdown has been completed on the display.
AUTOMATIC SHUT-OFF FUNCTION
▲
When the automatic shut-off function is set to “ON” in the TIME/CALENDAR SETTING display, the following energy-saving functions will be activated to help
extend the battery life.
● Regardless of the display modes, when the stopwatch is left untouched for one hour, the display becomes blank in order to minimize battery consumption.
● The current time will be displayed once every 10 seconds even while the display is blank, to indicate that the blank display is not caused by battery exhaustion.
● While the stopwatch or timer is measuring, the display will not become blank for the energy-saving functions.
● To return to the normal display, press either Button A, B, C or D. The last display before it became blank will be shown.
Automatic shut-off mark
When the automatic shut-off function
is set to “ON,” this mark appears in any
display mode except while the
stopwatch is in the setting mode.