Filter
Top Products
lnstructions
for
Assembly
of the PROSPOTItnessrM PC-1000
.
Before
assembly, choose a safe
location for
your
PROSPOFJitnessrM PC-1000. The PROSPOTlrressrM PC-
'1000
has a footprint of approximately 6'x
6'. The barbell is approximately 7' long. Locate
your
PROSPOTlrressrM
PC-'|000
away
from any source of
water. Do not
allow any
liquid
to be
near
the machine
or spilled on any electrical
part.
Do not insert any object
into the electrical
box.
.
Approximate assembly time is 1/2
hours.
o
A flat area of 8' x 8'will be
required to assemble and
properly
use the
PROSPOTlrtersrM
PC-1000.
.
You will need the following tools
and a helper to complete the assembly:
.
5 mm Allen
Wrench
.
14 mm Box End
Wrench
.
17 mm Box End Wrench
.
19 mm Box End
Wrench
.
Floor Padding, such as cardboard, to avoid scratching
your
floor during assembly.
.
A
good pair
of scissors
will be helpful in separating the
parts
from
one another while removing them from
the
caTtons.
o
HAND TIGHTEN
all
bolts. DO NOT fully tighten
bolts
until
instructed
to do so.
.
Before assembly, separate
and identify the righfsided
parts
from
the
left-sided
parts.
These
parts
are easily
distinguished by the
manner in which
the
pre-drilled
holes align with corresponding
parts.
or are
identified
by
"L"&"R"stickers.
.
The PROSPO"ffitnessrM
PC-1000 uses several different lengths of bolts. Be careful
to use the correct length
of bolt called for at each step of assembly.
Refer to the sizing charts
provided.
r
WARNING: Never
perform
any
maintenance
on the PROSPOT/itnesslM
PC-l000 while the Power Supply
is
plugged
into the wall !!!
STEP # 1: MAIN FRAME ASSEMBLY
1. Place the two Base Rails
(1
&
2) opposite each other in the center of the assembly
area as shown in the
lllustration. Place the Lower Cross Brace
(3)
between the two Base Rails
(1
& 2) so that the
side
pre-drilled
holes of the Base Rails
(1
& 2) align with the end holes of the Lower Cross Brace
(3).
2.
Carefully
thread the Cross Brace Wire Harness
(8)
through the corresponding
side
pre-drilled
holes
of the
Base Rails
(1
& 2) then
pull
the
Wire Harness
(8)
out of the top
holes
of the Base Rails
('l
& 2).
3. Attach the two Base Rails
(1
& 2) to the Lower Cross Brace
(3)
using two Upright
Support Plates
(6),
four
bolts
(22),
eight
washers
(18)
and four nuts
(20)
as shown. HAND TIGHTEN the bolts
at this time.
4. Attach the Right
Upright Guidepost
Assembly
(7,
10,23\
to the
Lower
Cross Brace
(3)
and
the Upright
Support Plate
(6)
attached on the right base rail
(1)
using two bolts
(22),
four washers
(
18)
and two nuts
(20)
as shown.
HAND TIGHTEN
the bolts at this time.
5. Attach the Left Upright Guidepost Assembly
(9,
12,23) to the Lower Cross Brace
(3)
and the Upright
Support Plate
(6)
attached on the left base rail
(2)
using two bolts
(22),
four washers
(
18)
and two nuts
(20)
as shown. HAND TIGHTEN the bolts at this time.
6. Plug
together both
of the Cross Rail Wire Harness
(8)
to lower ends of the
Spiral Signal Cables
(46)
Iocated
just
under the
perforated
Slider Shields on back
of the Screen Panels
(23).
__1__