Filter
Top Products
decrease the incline, the speed will automatically in
crease. The console will always attempt to keep
y
our pulse near a predetermined setting. When the
incline reaches the highest setting, the speed can-
n
ot be decreased any further. When the incline
reaches the lowest setting, the speed cannot be in-
creased any further.
Note: To stop the program temporarily, press the
START/PAUSE button. The TIME display will begin
to flash. To restart the program, press the
START/PAUSE button again. The program will re-
sume and the walking belt will return to the latest
speed setting. To terminate the program before the
program is completed, press the STOP button.
Follow your progress with the five displays and
the TRAINING ZONE monitor.
See TRAINING ZONE MONITOR on pages 13 and
14.
When you are finished exercising, stop the walk-
ing belt and remove the key.
Step onto the foot rails, stop the walking belt, and re-
move the key from the console. Store the key in a
secure place. In addition, move the on/off switch to
the “off” position. (See the drawing near the bottom
of page 11.)
The FITNESS TEST program is designed to measure
your relative fitness level. For the best results, the
FITNESS TEST should be taken at a time when your
energy level is high. The
FITNESS TEST
should not be
taken if you have already exercised during the day.
The FITNESS TEST program consists of seven 4-
minute periods, and is followed by a 2-minute cool-
down period. The speed and/or incline of the treadmill
will automatically increase at the beginning of each 4-
minute period.
To use the FITNESS TEST program, follow the steps
below.
Make sure that the key is fully inserted into the
console.
Stand on the foot rails
and insert the key.
Various displays and in-
dicators will light. Find
the clip attached to the
key, and slide it onto the
waistband of your clothing.
Select the FITNESS TEST program.
P
ress the FITNESS
TEST button. The in-
d
icator beside the
button will light. Note:
If the walking belt is
moving, it will slow to
a stop.
Enter your weight.
When the FITNESS TEST program is selected, the
letters “LbS” will flash in the CALORIES display.
You must enter your weight and age before this pro-
gram can be started. To enter your weight, see step
3 on page 12. If you have already entered your
weight, you must press one of the WEIGHT buttons
to verify the weight setting.
Enter your age.
After you have completed step 3, the letters “AGE”
will flash in the PULSE display. To enter your age,
see step 4 on page 12. If you have already entered
your age, you must press one of the AGE buttons to
verify the age setting.
Put on the pulse sensor.
The pulse sensor must be worn when the FITNESS
TEST program is used. To put on the pulse sensor,
see HOW TO USE THE PULSE SENSOR on page
8. Note: The FITNESS TEST program can be
started without your pulse being detected; however,
the program will automatically stop if your pulse is
not detected 4 minutes after the program is started.
Press the START/PAUSE button to start the pro-
gram.
When the START/
PAUSE button is
pressed, the TIME
display will begin
counting up. The
CALORIES display
will show “L 1” (level
1), indicating that the first 4-minute period of the
FITNESS TEST
program has begun. The incline of
the treadmill will automatically adjust to 3.0%, and
the walking belt will begin to move at 1.5 mph. Hold
the handrails and carefully begin walking.
When the TIME display reaches 4 minutes, the
CALORIES display will show “L 2,” indicating that
the second 4-minute period has begun. The incline
will increase to 4%, and the speed will increase to
2.5 mph. At the beginning of each 4-minute period,
7
1
2
3
4
5
6
8
HOW TO USE THE FITNESS TEST PROGRAM
W
C
D
FITNESS TEST
MAX.SPD.
START / PAUSE
17