Filter
Top Products
1,
o
10.
11.
12.
13.
14.
Insert one (1) 3 X 2 IN. END CAP into the top of the UPRIGtIT FRAME, and two (2) 2 IN. SQ.
CAPS into the BASE of the UPRIGHT FRAME as shown on drawing. Repeat this step for the second
UPRIGHT FRAME.
SECURELY assemble both UPRIGHT FRAMES to the CROSS BRACE as shown on drawing using
four (4) 1/2 X 3 IN. BOLTS, four (4) 1/2 IN. WASHERS, and four (4) 1/2 IN. LOCK
(IMPORTANT: ~ ANGLE BRACKETS ON ~ CROSS BRACE ARE OFFSET, PLEASE
MAKE SURE THAT ~ LONGEST END OF TIlE BRACKET IS FACING IYP BEFORE
ASSEMBLY)
SECURELY assemble the BENCH FRAME to the CROSS BRACE as shown on dmw~ng using two (2)
1/2 X 3 IN. BOLTS, two (2) 1/2 IN. WASHERS, and two (2) 1/2 IN. LOCK NUTS. Attach one 2"
cover cap to the BENCH FRAME as shown.
Insert two (2) 1/2 IN. FLANGE BEARINGS into each end of the BUSHING of the BLENCH FRAME
shown on drawing.
SECURELY assemble the BENCH SLIDE to the BUSHING of the BENCH FRAME as shown on
drawing, using one (1) 1/2 X 3-1/2 IN. BOLT one (1) 1/2 IN. LOW HT LOCK
Attach eight (8) 1-1/2 X 3/4" GLIDES to the WOLFF SLEEVE (FOUR ON EACH Ell’D) as shown
(DETAIL A) using the following steps:
¯
Thoroughly clean all surfaces where the GLIDES are to be attached.
¯
Remove the GLIDES from the paper backing and f’mrdy apply them to all shown surfaces.
Insert one (1) U-PIN through the BUSItlNG of the WOLFF SLEEVE as shown on ctrawing, and attach
one (1) PAL NUT to the end of the U-PIN.
SECURELY Assemble one (1) SPRING PIN ASSEMBLY to the SPRING PIN BARI~’,L, of the
WOLFF SLEEVE as shown in (DETAIL B). (!!! IMPORTANT !!! TIGHTEN TLTE NUT OF
SPRING PIN ASSEMBLY SECURELY)
Pull back the SPRING PIN on the WOLFF SLEEVE and slide it over the end of the BENCH SLIDE as
shown on drawing. Engage the SPRING PIN into one of the adjustment holes. Secure tk~e WOLFF
SLEEVE in place with one (1) 3-PRONG KNOB.
LOOSELY assemble one (1) 3 PRONG KNOB to the UPRIGHT TUBE of the BENCI~[ FRAME
shown on drawing. (TI:[IS WILL BE USED TO SECURE ATTACHMENTS IN PLACE)
Attach one (1) 1-1/4 IN. SQ. RUBBER BUMPER to the SLIDE SUPPORT as shown orb drawing.
SECURELY assemble the SLIDE SUPPORT to the end of the BENCH SLIDE as shown on drawing
using one (1) 3/8 X 2-3/4 IN. BOLT, two (2) 3/8 IN WASHERS, and one (1) 3/8 IN. LOCK
Attach two (2) 1 X 1 GLIDES to file top of the BENCH FRAME where the SLIDE SUPPORT makes
contact. See drawing.
Assemble the SEAT PAD to the WOLFF SLEEVE, start by sliding t~vo (2) HINGE TABS over the
PIN of the WOLFF SLEEVE (ONE ON EACH SIDE) as shown on drawing, and SECURELY
assemble each tlINGE TAB to the SEAT PAll using two (2) 3/8 X 1-1/4 IN. BOLTS mid two (2)
IN. WASHERS. (MAKE SURE BOTH ltINGE TABS ARE ALL THE WAY ON TIlE PIN)
Part # 6657601
3 Revision: it0/28/96