Filter
Top Products
2
P/N 214982A 01/03
ENGLISH INSTRUCTIONS
IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1
OF THIS OWNERS MANUAL
1.
Insert axle (2) into tank (1) as shown to secure wheel (3) and eyebolt
(57) into position. Repeat procedure for opposite side.
2.
Position front cover (47) on top of tank (1) as shown, insert eye bolts
(57) through cover, snapping front cover over axles (2) at the same time.
Tighten completely.
3. Mark pole sections with tape as shown.
4. IMPORTANT! Center alignment slot of middle pole section (5) in a
lower hole of top pole section (4) as shown. While maintaining
alignment, bounce top pole section (4) and middle section (5) together
as shown until they no longer move toward taped reference mark.
Upright assembly. NOTE: Pole sections should have a 3-1/2” (9 cm)
overlap minimum.
5. IMPORTANT! Center alignment slot of lower pole section (6) in a
lower hole of middle pole section (5) as in step 4. While maintaining
alignment, bounce assembly and lower pole section (6) together as
shown until they no longer move toward taped reference mark. NOTE:
Pole sections should have a
3-1/2” (9 cm) overlap minimum.
6. Insert bolts (7) into bracket (9) as shown. Install bolt (14) through
bracket (9) and bottom pole section (6) and secure with nut (12) as
shown.
7. Carefully tip unit forward and secure pole assembly to tank (1) with
washers (13) and nuts (16) as shown.
8. Install rod (11) through bottom pole section (6) as shown. Install eye
bolts (8) onto rod (11) as shown.
9. Secure cover (47) to rod (11) using washers (55) nuts (10) and bolt
covers (15) as shown.
10. Install pole mount bracket (17) and reinforcement bracket (58) with
carriage bolts (18) as shown. Tighten flange nuts (16) completely.
11. Attach spacers (22, 23) to pole mount bracket (17) with bolts (21),
washers (19), and nuts (20) as shown. IMPORTANT! Tighten just
until washers (19) stop moving.
12. Attach covers (24) onto pole mount bracket (17) with carriage bolt (25)
and nut (16) as shown. IMPORTANT! Loop end of pin lanyard (27)
over carriage bolt (25) during this assembly. NOTE: Assemble
lanyard (27) to locking pin (26) as shown.
13. Apply logo and height indicator labels (29) to adjustment rod (28) as
shown. Attach handle parts (32, 33) to adjustment rod with screw (31),
carriage bolts (30), and flange nuts (16) as shown. IMPORTANT!
Indicator labels should be applied as close to holes as possible to
prevent labels from being damaged during height adjustment.
14. Insert handle assembly through pole mount assembly as shown. Lock
pole assembly in place at the 10’ (3.05 m) mark with pin (26).
15. Install spacers (36) onto backboard brackets (35), with bolts (21, 56) and
lock nuts (20, 50) as shown.
IMPORTANT! Test fit bolts (37) into holes of brackets (35) and
carefully rock them in a circular motion to ream out paint from
holes if necessary.
16. Attach lower elevator tubes (40) and counter balance spring (41) to
backboard support brackets (35) using spacers (34), bolt (37), and nut
(39) as shown.
17. Starting with nuts (16) flush against bracket (35) secure rim (42) and
bracket to backboard. IMPORTANT! For spring loaded rim assembly,
refer to instructions included with rim hardware. NOTE: Do not use
washers here on spring return style rim. NOTE: Mounting nuts and bolts
supplied with rim hardware.
18. Attach upper elevator tubes (43) to backboard support brackets (35)
using spacers (34), bolt (37), and nut (39) as shown.
19. Support pole on sawhorse. Attach backboard assembly to top pole
section (4) as shown. Install pole cap (46). NOTE: Two people are
recommended for this step. Use caution; elevator assembly is heavy.
20. Install upper elevator tubes (43) to triangle plates (45) as shown. Install
handle assembly to lower elevator tubes (40) using bolt (37), spacers
(44), and nut (39) as shown. NOTE: Before going on to next step, set
adjustable system assembly to the 10’ (3.05 m) setting.
WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS.
21. Insert bolt (37) through left side upper elevator tube (43), then stretch
spring (41) onto bolt (37). Insert bolt (37) through right side upper
elevator tube (43) and secure with nut (39).
22. Roll completed assembly to desired position. Fill tank with water
(approx. 28 gallons (106 Liters)) or sand (approx. 225 lbs. (102 kg)) and
snap cap (49) in place. Secure assembly to ground using rope (52) and
tie down stake (53).
IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in
sub-freezing climates.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN
EMPTY, MAY TIP OVER.
23. Apply height adjustment and moving label (54) to front of pole as shown.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
24. While holding handle, remove pin (26).
25. Move elevator up or down to desired height.
26. Replace pin (26) full length to lock system at desired height.