Filter
Top Products
12
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
13
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
CENTERING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment. Before operating the
treadmill, make sure the belt is centered and remains
centered to maintain smooth operation.
CAUTION: Do not run belt faster than 1/2 mph while
centering. Keep fingers, hair and clothing away from
belt at all times.
If the running belt is too far to the right side:
With the treadmill running at 1/2 mph, turn the right
adjustment bolt clockwise 1/4 TURN at a time (using
the supplied Allen wrench). Check the belt alignment.
Allow belt to run a full cycle to gauge if more adjustment
is needed. Repeat if necessary, until the belt remains
centered during use.
If the running belt is too far to the left side:
With the treadmill running at 1/2 mph, turn the right
adjustment bolt counter-clockwise 1/4 TURN at a time
(using the supplied Allen wrench). Check the belt
alignment. Allow belt to run a full cycle to gauge if more
adjustment is needed. Repeat if necessary, until the
belt remains centered during use.
Belt is too far to the right side
Belt is too far to the left side
TENSIONING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment.
CAUTION: Running belt should NOT be moving during
tensioning. Over-tightening the running belt can
cause excessive wear on the treadmill as well as its
components. Never over-tighten the belt.
If you can feel a slipping sensation when running on the
treadmill, the running belt must be tightened. In most
cases, the belt has stretched from use, causing the
belt to slip. This is a normal and common adjustment.
To eliminate this slipping, TURN THE TREADMILL OFF
and tension BOTH THE REAR ROLLER BOLTS using the
supplied Allen wrench, turning them 1/4 TURN to the
right as shown. Turn the treadmill on and check for
slipping. Repeat if necessary, but NEVER TURN the
roller bolts more than 1/4 turn at a time. Belt is properly
tensioned when the slipping sensation is gone.
Note: There is a thin protective sheet of clear plastic on the overlay of the console and should be removed.
A) MONITOR DISPLAY: Speed, Time, Pulse, Distance, Incline, Calories.
B) STOP: Press to pause/end your workout. Hold for 3 seconds to reset the treadmill.
C) START: Press to begin exercising or to start your program.
D) ENTER: Used to select Program, Level, Time, and confirm speed choice. Press to change display feedback
during workout, Hold to scan.
E) QUICK SPEED KEYS: Used to reach desired speed more quickly. (Choose a speed and then press ENTER to
confirm)
F) INCLINE ARROW KEYS: Used to adjust incline in small increments (0.5% increments).
G) SPEED ARROW KEYS: Used to adjust speed in small increments (0.1 mph increments).
H) SAFETY KEY POSITION: Enables treadmill when safety key is inserted.
I) READING RACK: Holds reading material. (Remove sales sticker before use)
j) INCLINE INDICATORS: Displays current incline percentage
K) SPEED INDICATORS: Displays current speed
T R E A D M I L L O P E R AT I O N
A
I
A
B HGFE
C
J K
D
TIME
DISTANCE
CALORIES
PULSE
INCLINE
SPEED
1MPH
2MPH
3MPH
4MPH
5MPH
6MPH
7MPH
8MPH
9MPH
10MPH
PRESS
ENTER
TO SET
SPEED
MAGNETIC KEY
1.3T
INCLINE SPEED
INCLINE % SPEED MPH
STOP
HOLD TO RESET
START
QUICK START
ENTER
CHANGE DISPLAY
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
1.3T_Rev.1.4.indd 12-13 7/12/06 8:25:12 AM