Filter
Top Products
Operation Guide 3134 3205
12
Recovery Times
The table below shows the amount exposure that is required to take the
battery from one level to the next.
• The above exposure time values are all for reference only. Actual required
exposure times depend on lighting conditions.
Approximate Exposure Time
Level 5 Level 4 Level 3 Level 2 Level 1
1 hour 12 hours 4 hours
3 hours 58 hours 16 hours
5 hours 119 hours 33 hours
52 hours - - - - - - - - - - - - - - - -
Exposure Level
(Brightness)
Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy
Day (5,000 lux)
Indoor Fluorescent
Lighting (500 lux)
▲
▲
▲
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• In the Timekeeping Mode, an indicator moves along the ring around the
display as seconds advance.
• The tide graph shows tidal movements for the current date in accordance
with the current time as kept in the Timekeeping Mode.
• The Moon phase indicator shows the current Moon phase in accordance
with the current date as kept in the Timekeeping Mode.
• In the Timekeeping Mode, you can press E to toggle the display contents
as shown below.
Day of week
Month – Day
Day of the Week Screen
PM indicator
Hour :
Minute
Second
Barometric Pressure
Graph Screen
Month – Day
Barometric
pressure
graph
Press E.
▲
▲
Hour :
Minute
Second
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of which represents
the time zone where that city is located. When setting the time, it is important
that you first select the correct city code for your Home City (the city where
you normally use the watch). If your location is not included in the preset city
codes, select the preset city code that is in the same time zone as your
location.
• Note that all of the times for the World Time Mode city codes are displayed
in accordance with the time and date settings you configure in the
Timekeeping Mode.
To set the time and date manually
1. In the Timekeeping Mode, hold down E until the city code starts to flash,
which indicates the setting screen.
2. Use A and C to select the city code you want.
• Make sure you select your Home City code before changing any other
setting.
• For full information on city codes, see the “City Code Table”.
Year
Second
Hour
Minute
Day
Month
12/24-Hour
Format
Power
Saving
Barometric
Pressure Unit
Altitude Unit
Temperature
Unit
City Code
DST
3. Press D to move the flashing in the sequence shown below to select the
other settings.
5. Press E to exit the setting screen.
Note
• Auto DST (
) can be selected only while
LON
,
PAR
,
BER
,
ATH
,
NYC
,
CHI
,
DEN
,
LAX
,
ANC
,
HNL
,
TYO
,
SEL
, or
HKG
is
selected as the Home City code. For more information, see “Daylight
Saving Time (DST)” below.
Do this:
Press A
.
Use A (+) and C (–).
To do this:
Reset the seconds to
00
Change the hour or minute
Change the year
Change the month or day
Screen
• You also need to enter the Timekeeping Mode in order to configure the
following settings.
Power saving on/off (“To turn Power Saving on and off”)
Temperature, barometric pressure, and altitude units (“To select the
temperature, barometric pressure, and altitude units”)
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour
from Standard Time. Remember that not all countries or even local areas use
Daylight Saving Time.
The time calibration signals transmitted from Mainflingen (Germany), Anthorn
(England), or Fort Collins (the United States) include both Standard Time and
DST data. When the Auto DST setting is turned on, the watch switches
between Standard Time and DST (summer time) automatically in accordance
with the signals.
• Though the time calibration signal transmitted by the Fukushima and
Fukuoka/Saga, Japan transmitters include summer time data, summer time
currently is not implemented in Japan (as of 2007).
• The default DST setting is Auto DST (
) whenever you select
LON
,
PAR
,
BER
,
ATH
,
NYC
,
CHI
,
DEN
,
LAX
,
ANC
,
HNL
, or
TYO
as your Home City code.
• If you experience problems receiving the time calibration signal in your
area, it probably is best to switch between Standard Time and Daylight
Saving Time (summer time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down E until
the city code starts to flash, which indicates
the setting screen.
2. Press D and the DST setting screen appears.
3. Use A to cycle through the DST settings in
the sequence shown below.
Auto DST ( ) DST off ( ) DST on ( )
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
•
If you change your Home City to one that is within the same transmitter
area, the current DST setting (AUTO) will be retained. If you change to a
city that is outside your current transmitter area, DST will be turned off
automatically.
Transmitter area city codes
•
HKG, SEL, and TYO
• LAX, DEN, CHI, NYC, ANC, and HNL
• LON, PAR, BER, and ATH
• All other city codes
4. When the setting you want is selected, press E to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Reference
This section contains more detailed and technical information about watch
operation. It also contains important precautions and notes about the various
features and functions of this watch.
Moon Phases and Moon Age
The Moon goes through a regular 29.53-day cycle. During each cycle, the
Moon appears to wax and wane as the relative positioning of the Earth,
Moon, and Sun changes. The greater the angular distance between the Moon
and the Sun,* the more we see illuminated.
* The angle to the Moon in relation to the direction at which the Sun is visible
from the Earth.
This watch performs a rough calculation of the current Moon age starting
from day 0 of the moon age cycle. Since this watch performs calculations
using integer values only (no fractions), the margin for error of the displayed
Moon age is ± 1 day.
Do this:
Use A (east) and
C(west).
Press A.
Press A.
To do this:
Change the city code
Cycle between Auto DST (
),
Daylight Saving Time (
) and
Standard Time (
).
Toggle between 12-hour (
12H
)
and 24-hour (
24H
) timekeeping.
Screen
• The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use A and/
or C to change it as described below.