Filter
Top Products
Operation Guide 5143
E-69
To check whether a time zone is AM or PM
In the World Time Mode, press B and the
x
Second Hand
will move to either A (AM) or P (PM).
The
x
x
Second Hand will return to the city code you
selected after about one second.
To specify standard time or daylight saving time (DST)
for a city
In the World Time Mode, unlock the crown and then pull 1.
it out to enter the city setting mode.
Rotate the crown to move the 2.
x
Second Hand to the
city code whose setting you want to change. See “To
view the time in another time zone” (page E-67) for more
information.
@
E-68
If you think that the time indicated for the selected World Time City is not correct, x
it probably means that there is something wrong with your Home City settings.
Use the procedure under “To confi gure Home City settings” (page E-32) to
correct the Home City settings.
After selecting the city you want, push the crown back in to return to the World Time 3.
Mode. Next, lock the crown.
Rotating the ring without pushing it down as far as it will go will change the
x
settings of the watch. When locking the crown, be sure to press down fi rmly on
the ring as you rotate it.
E-67
To view the time in another time zone
Unlock the crown and then pull it out.1.
The
x
x
Second Hand points to the currently selected World Time city code.
The mode pointer will point to either
x STD (standard time) or DST (daylight saving
time) on the
v
Mode Disk, which indicates the current daylight saving time
setting.
If you do not perform any operation with the crown for about three minutes after
x
pulling it out, crown operations will become disabled and the watch hands will no
longer move when you rotate the crown. If this happens, push the crown back in
and then pull it out again.
Rotate the crown to move the 2.
x
Second Hand to the city code you want to select
as the World Time City.
Each time you select a city code, the
x
z
Hour Hand,
c
Minute Hand, and
n
Day
move to the current time and date for that city code. For details about city codes,
see the “City Code Table” at the back of this manual.
E-66
Checking the Current Time in a Different Time Zone
You can use World Time to view the current time in one of 29 time zones around the
globe. The currently selected city is called the “World Time City”.
Hands and Indicators
z
Hour Hand: Indicates the hour of the current time in the
World Time City.
x
Second Hand: Indicates the currently selected World
Time City.
Pressing
x B causes the
x
Second Hand to move to
A (AM) or P (PM).
c
Minute Hand
v
Mode Disk: WT aligned with mode pointer.
n
Day
B 6
+@
>
NYC (NEW YORK)
E-65
To check the AM/PM setting of the alarm
In the Alarm Mode, press B and the
x
Second Hand will move to either A (AM) or
P (PM).
The
x
x
Second Hand will return to the current ON/OFF setting after about one
second.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm between on and off. The
x
Second
Hand will indicate the current ON/OFF setting.
To stop the alarm
Press any button or press the crown button.
E-64
After the setting is the way you want, push the crown back in to exit the alarm 6.
setting mode. Next, lock the crown.
The alarm always works based on the time kept in the Timekeeping Mode.
x
The watch will return to the Timekeeping Mode automatically if you do not x
perform any operation in the Alarm Mode for about two or three minutes.
Rotating the ring without pushing it down as far as it will go will change the x
settings of the watch. When locking the crown, be sure to press down fi rmly on
the ring as you rotate it.
E-63
Rotate the crown to set the alarm time.3.
Rotating the crown two full consecutive turns away from you will cause the x
c
Minute Hand to start moving clockwise. Rotating the crown another two full
consecutive turns away from you will cause the
c
Minute Hand to start moving
at high speed. To stop hand movement, press any button or rotate the crown one
full turn towards you.
Press 4. B to switch to the hour setting mode.
The x
z
Hour Hand will move slightly left and right to indicate the
z
Hour Hand
setting mode.
If you want to change the hour setting without changing the minute setting, skip
x
step 4 above.
When adjusting the alarm time setting, check to make sure that the x
x
Second
Hand correctly indicates A (AM) or P (PM).
Rotate the crown to adjust the hour setting only.5.
Rotating the crown two full consecutive turns away from you will cause the
x
z
Hour Hand to start moving clockwise.
E-62
To change the alarm time setting
Press the crown button to navigate to the Alarm Mode.1.
The mode pointer will point to
x AL on the
v
Mode Disk.
Unlock the crown and then pull it out to enter the alarm setting mode.2.
The
x
x
Second Hand will move to either A (AM) or P (PM).
If you do not perform any operation with the crown for about three minutes after
x
pulling it out, crown operations will become disabled and the watch hands will no
longer move when you rotate the crown. If this happens, push the crown back in
and then pull it out again.
You can toggle between the hour and minute setting mode, and the hour only
x
setting mode by pressing B.
Hour/Minute Hour
B
E-61
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
Hands and Indicators
z
Hour Hand: Indicates the currently set alarm time hour.
x
Second Hand: Indicates the current alarm ON/OFF
setting.
Pressing
x B causes the
x
Second Hand to move to the
current A (AM) or P (PM) setting.
c
Minute Hand: Indicates the currently set alarm time
minute.
v
Mode Disk: AL aligned with mode pointer.
B>
+@
E-60
Pulling out the crown to perform a crown operation while a Countdown Timer x
countdown or elapsed time measurement is in progress will automatically stop the
ongoing Countdown Timer operation and reset to the countdown start time.
Elapsed Time Measurement Following Countdown
When the countdown reaches zero, the watch starts to count up elapsed time in
one-second increments, for up to 24 hours. When the watch switches to elapsed time
measurement, the hands automatically switch to clockwise movement.
You can pause and restart an elapsed time operation by pressing
x A. While an
elapsed time operation is paused, pressing B resets to the countdown start time.
To stop the alarm
Press any button or press the crown button.
Note
Pressing any button or pressing the crown button while the alarm is sounding
x
simply stops the alarm sound. It does not stop the elapsed time operation that
started when the end of the countdown was reached. To stop the elapsed time
operation, press A.