Filter
Top Products
Operation Guide 5143
E-39
Change the Home City and daylight saving time (DST) 2.
settings, if you want.
For details about these settings, see steps 3 and 4
x
under “To confi gure Home City settings” (page E-32).
Hold down 3. B for about two seconds. This will enter the
time setting mode.
The
x
x
Second Hand will move to A (AM) or P (PM).
In the following steps, each press of
x B cycles
between settings as shown below.
Home city/DST Hour/Minute Hour
Month DayYear
BB
BB
BB
+
@
B
E-38
Confi guring Current Time and Date Settings
To change the current time setting
In the Timekeeping Mode, unlock the crown and then 1.
pull it out.
This will cause the
x
x
Second Hand to move to the city
code of the currently selected Home City.
At this time, the mode pointer will point to the current
x
daylight saving time setting (STD or DST).
If you do not perform any operation with the crown
x
for about three minutes after pulling it out, crown
operations will become disabled and the hand will not
move if you rotate the crown. If this happens, push
the crown back in and then pull it out again.
@
TYO (TOKYO)
E-37
After the settings are the way you want, push the crown back in to return to the 3.
Timekeeping Mode. Next, lock the crown.
Rotating the ring without pushing it down as far as it will go will change the
x
settings of the watch. When locking the crown, be sure to press down fi rmly on
the ring as you rotate it.
E-36
To toggle the Home City time between standard time and daylight saving time
Perform steps 1 through 3 under “To confi gure Home 1.
City settings” on page E-32.
Each time you select a city code, the
x
z
Hour Hand
and
c
Minute Hand move to the current time for that
city code.
Press 2. A to toggle the time for the currently selected
city code between standard time and daylight saving
time.
The mode pointer will point to either
x STD (standard
time) or DST (daylight saving time) on the
v
Mode
Disk, which indicates the current daylight saving
time setting.
+B
>
E-35
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
Note that you cannot switch between
x STD (standard time) and DST (daylight
saving time) while UTC* is selected as your Home City.
Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. The *
reference point for UTC is Greenwich, England.
E-34
Press 4. A to toggle the currently selected city code
between standard time and daylight saving time.
In the city code setting mode, the
x
v
Mode Disk
indicates STD (standard time) or DST (daylight
saving time).
For details about the Daylight Saving Time setting,
x
see “Daylight Saving Time (DST)” (page E-35).
After the settings are the way you want, push the crown 5.
back in to return to the Timekeeping Mode. Next, lock
the crown.
Rotating the ring without pushing it down as far as it
x
will go will change the settings of the watch. When
locking the crown, be sure to press down fi rmly on
the ring as you rotate it.
>
E-33
If you do not perform any operation with the crown x
for about three minutes after pulling it out, crown
operations will become disabled and the watch
hands will no longer move when you rotate the crown.
If this happens, push the crown back in and then pull
it out again.
For details about city codes, see the “City Code
x
Table” at the back of this manual.
Rotate the crown to move the 3.
x
Second Hand to the
city code you want to select as your Home City.
Each time you change to a different city code, the
x
z
Hour Hand,
c
Minute Hand, and
n
Day move
to the current time and date for that city code. Also,
the
v
Mode Disk rotates until the mode pointer is
pointing at either STD or DST (see step 4 of this
procedure below).
@
+
6
B
>
E-32
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To confi gure Home City settings
Note
This watch does not have a city code that
x
corresponds to Newfoundland.
Press and hold the crown button (without unlocking 1.
the crown) for at least two seconds.
This will enter the Timekeeping Mode (page E-29).
x
Unlock the crown and then pull it out.2.
This will cause the x
x
Second Hand to move to the
city code of the currently selected Home City.
This indicates the city code setting mode.
x
@
TYO (TOKYO)
E-31
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. To enter the
Timekeeping Mode from another mode, press and hold the crown button (without
unlocking the crown) for at least two seconds.
Hands and Indicators
z
Hour Hand
x
Second Hand
c
Minute Hand
v
Mode Disk: TM aligned with mode pointer.
n
Day
+
6>
@B
E-30
From any other mode, hold down C for about two seconds to enter the Stopwatch
LAP Mode. The
v
Mode Disk will rotate until the lap pointer points at the current lap
number (1 through 5, or
).
To return to the Timekeeping Mode, hold down C or the crown button for about two
seconds.