Filter
Top Products
Operation Guide 2914
6
Alarms
❚
Daily Alarms (AL1 to AL4)
The watch beeps for about 10 seconds when an alarm time is
reached.
❚
Snooze Alarm (SNZ)
With the snooze alarm, the watch beeps for 10 seconds when the
alarm time is reached, and up to seven times at five-minute
intervals thereafter (approximately 30 minutes total). Pressing any
button stops the beeper, but the alarm will sound again after five
minutes.
❚
To set an alarm time
1. In the Alarm Mode, use the
DD
DD
D button to scroll
through the alarm screens
until the one whose
setting you want to
change is displayed.
Alarm 3
(AL3)
Alarm 1
(AL1)
Alarm 2
(AL2)
Alarm 4
(AL4)
Hourly Time
Signal (SIG)
Snooze Alarm
(SNZ)
2. Hold down the
AA
AA
A button
for about two seconds
until the hour digits start
to flash on the display.
• This also causes the alarm on
indicator to appear and
automatically turns on the
alarm.
3. Use the
CC
CC
C button to
select the digits you want
to change.
• Each press of the C button
moves the flashing between
the hour digits and minute
digits.
Alarm Number
(Next alarm)
Alarm on indicator
Hour
4. Use the
DD
DD
D (+) and
BB
BB
B(–)
buttons to change the
currently selected digits.
• Holding down either button
changes the setting at high
speed.
Repeat steps 3 and 4 for the hour digits and the minute
digits to set the time you want.
• When setting the hour, make sure you specify AM (A) or PM (P)
correctly when using 12-hour timekeeping, or that you specify the
correct 24-hour time.
• The same 12-hour/24-hour format you select for your home time
is also applied in the Alarm Mode.
5. When the setting is the way you want, press the
AA
AA
A
button.
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
❚
To turn an alarm on and off
1. In the Alarm Mode, use the
DD
DD
D button to display the
screen for the alarm you want to turn on or off.
2. Press the
BB
BB
B button to toggle the displayed alarm on
(alarm on indicator displayed) or off (alarm on indicator
not displayed). Turning on the snooze alarm will cause
the “SNZ” indicator to appear on the display.
Alarm 1
Snooze On Indicator
Alarm On IndicatorAlarm On Indicator
Snooze Alarm
(Increase)
(
Decrease
)
❚
To stop the alarm beeper
Press any button.
• In the case of the snooze alarm the alarm will sound again in
about five minutes. “SNZ” flashes on the display during the
five-minute period between snooze alarms (indicating that the
alarm will sound again).
• The snooze alarm will be canceled automatically when any of the
following occurs while the SNZ indicator is flashing on the display.
• If you turn off the snooze alarm
• If you display the snooze alarm setting screen
• If you display the Timekeeping Mode setting screen
❚
To test the alarm
In the Alarm Mode, hold down the D button to sound the alarm.
Using the Alarm and Hourly Time Signal
The stopwatch measures elapsed time in units of 1/100 second up
to 23 hours 59 minutes, 59.99 seconds (24 hours). When the
maximum limit is reached, the elapsed time automatically returns
to zero and timing continues from there.
❚
Performing Stopwatch Operations
In the Stopwatch Mode, press the
CC
CC
C button to start and stop
elapsed time measurement.
• During elapsed time measurements, segments in the graphic
dials appear and disappear to indicated the passage of time.
(Start/Stop)
(Split/Reset)
Minutes
Seconds Hours
1/100
Second
• Pressing the B button while timing is being performed
freezes the current elapsed time on the display and
displays the “SPL” (split) indicator, while elapsed timing
continues internally.
• Changing to another mode while a split time is displayed
clears the split time.
• Pressing the B button while elapsed time measurement is
stopped resets the stopwatch to all zeros.
❚
Elapsed Time Measurement
Stop ResetStart
Cumulative Elapsed Time Measurement
Pressing the D button to restart the stopwatch without resetting it
to all zeros causes the elapsed time measurement to resume from
where it was last stopped.
❚
Split Time Measurement
Record Split Release Split ResetStopStart
Split Indicator
Split Time Display
Clears split
time.
❚
1st and 2nd Place Finishers
Start 1st finish
(Displays time
of 1st finish.)
2nd finish Displays time
of 2nd finish.
Reset
Stopwatch Mode
Hourly Time Signal
The hourly time signal causes the watch to beep twice every hour
on the hour.
❚
To turn the hourly time signal on and off
1. In the Alarm Mode, use the
DD
DD
D button to display the
hourly time signal screen.
2. Press the
BB
BB
B button to toggle the hourly time signal on
or off.
• Turning on the hourly time signal causes the hourly time signal
indicator to appear on the display. The watch will beep twice
every hour on the hour.
Hourly Time Signal
On Indicator
Hourly Time Signal Screen