Filter
Top Products
Operation Guide 5192
E-40
To specify standard time or daylight saving time (DST) for a time zone
Hold down
A for two
seconds
> 6
In the World Time Mode, use 1. D to select the city code
for the time whose setting you want to change.
Wait until the
x
n
Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
Hold down 2. A for about two seconds until the watch
beeps. This will cause the
v
Left Dial Hand to toggle
between DST (daylight saving time) and STD (standard
time).
Note that you cannot switch between
x STD (standard
time)/DST (daylight saving/summer time) while UTC is
selected as the World Time City.
Note that the
x STD (standard time)/DST (daylight
saving/summer time) setting affects only the currently
selected time zone. Other time zones are not affected.
E-41
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
The following example shows what happens when the Home City and World Time
City are swapped while the Home City originally is TYO (Tokyo) and the World Time
City is NYC (New York).
Home City World Time City
Before swapping
Tokyo
10:08 p.m.
(Standard time)
New York
9:08 a.m.
(Daylight saving time)
After swapping
New York
9:08 a.m.
(Daylight saving time)
Tokyo
10:08 p.m.
(Standard time)
E-42
To swap your Home City and World Time City
In the World Time Mode, use 1. D to select the World
Time City you want.
In this example, you would move the
x
x
Second Hand
to NYC in order to select New York as the World
Time City.
Wait until the
x
n
Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
6
@
E-43
Hold down 2. B for about three seconds until the watch
beeps.
This will make the World Time City (
x NYC in this
example) your new Home City. At the same time, it
will change the Home City you had selected prior to
step 2 (TYO in this example) to your World Time City.
After swapping the Home City and World Time City,
x
the watch will stay in the World Time Mode. The
x
Second Hand will point to your new World Time City
(TYO in this example).
The
x
n
Right Dial Hands will indicate the current time
in your new World Time City.
@ 6
E-44
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
Hand Functions
x
Second Hand: Indicates the current alarm ON/OFF
setting.
v
Left Dial Hand: Points to ALM.
n
Right Dial Hands: Indicate the current alarm time
setting in 24-hour format.
> 6
@
E-45
To change the alarm time setting
Use 1. C to move the
v
Left Dial Hand to ALM.
This indicates the Alarm Mode. x
Use 2. D (+) and B (–) to change the alarm time setting.
Each press of either button will move the x
n
Right Dial Hands one minute.
Holding down x D or B will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
The alarm always works based on the time kept in the Timekeeping Mode.
x
The watch will return to the Timekeeping Mode automatically if you do not x
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm on and off. The
x
Second Hand will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
E-46
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or date of the watch to be off.
If this happens, perform the applicable home position adjustment procedures in this
section.
Hand home position adjustment is not required if the time and day settings are
x
correct.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in the home position adjustment mode. In either case,
any adjustments you made before the watch returned to the Timekeeping Mode will
be applied.
E-47
To adjust home positions
Hold down 1. C for about two seconds until the
x
Second
Hand stops and then starts moving again.
Hold down 2. D for about three seconds.
The
x
x
Second Hand will start to move when you fi rst
press D. Keep D depressed until the
x
Second
Hand stops.
The watch is now in the home position adjustment
x
mode.
The watch will exit the home adjustment mode x
automatically if you do not perform any operation for
about two or three minutes.
First is
x
x
Second Hand home position adjustment.
If the x
x
Second Hand moves to 12 o’clock, it is in the
correct home position. If it doesn’t, use D to move it
to 12 o’clock.
B +
* 6> 5
@
E-48
When adjusting a hand or the date home position, it is recommended that after x
you move to a proper home position, you press B to move the setting back one
step. Next, press D again to return it to the home position. This helps to ensure
better home position adjustment accuracy.
Each press of
x C in the home position adjustment mode will cycle through the
adjustment settings as shown below.
x
Second
z
Hour/
c
Minute/
b
24-hour
n
Right Dial Hands
v
Left Dial Hand
m
Day
E-49
After confi rming that the 3.
x
Second Hand is at the proper
home position, press C. This will switch to
z
Hour
Hand and
c
Minute Hand home position adjustment.
The x
z
Hour Hand and
c
Minute Hand are at their
proper home positions if they both move to 12 o’clock.
The
b
24-hour Hand also will move along with
z
Hour Hand movement, and cannot be adjusted
individually. If the hands are not positioned correctly,
use D (+) and B (–) to move them to their proper
home positions.
After confi rming that the 4.
z
Hour Hand and
c
Minute
Hand are in their correct home positions, press C.
This will switch to
n
Right Dial Hands home position
adjustment.
The
x
n
Right Dial Hands are at their proper home positions if they both move
to 24. If the hands are not positioned correctly, use D (+) and B (–) to move
them to 24.
B +
* 6
@