Filter
Top Products
Operation Guide 5142
L-3
City Code City
UTC Offset/
GMT Differential
JEDDAH (JED) Jeddah +3
TEHRAN (THR) Tehran +3.5
DUBAI (DXB) Dubai +4
KABUL (KBL) Kabul +4.5
KARACHI (KHI) Karachi +5
DELHI (DEL) Delhi +5.5
DHAKA (DAC) Dhaka +6
YANGON (RGN) Yangon +6.5
BANGKOK (BKK) Bangkok +7
HONG KONG
(HKG) Hong Kong +8
TOKYO (TYO) Tokyo +9
ADELAIDE (ADL) Adelaide +9.5
SYDNEY (SYD) Sydney +10
NOUMEA (NOU) Noumea +11
WELLINGTON
(WLG) Wellington +12
L-2
City Code Table
City Code City
UTC Offset/
GMT Differential
PAGO PAGO (PPG) Pago Pago –11
HONOLULU (HNL) Honolulu –10
ANCHORAGE
(ANC) Anchorage –9
LOS ANGELES
(LAX) Los Angeles –8
DENVER (DEN) Denver –7
CHICAGO (CHI) Chicago –6
NEW YORK (NYC) New York –5
SANTIAGO (SCL) Santiago –4
RIO Rio De Janeiro –3
F. DE NORONHA (FEN) Fernando de Noronha –2
PRAIA (RAI) Praia –1
UTC
0
LONDON (LON) London
PARIS (PAR) Paris +1
ATHENS (ATH) Athens +2
L-1
City Code Table
E-106
World Time: 29 cities (29 time zones) and Coordinated Universal Time
Other: Daylight Saving Time (summer time) / Standard Time
Stopwatch: Measuring capacity: 59'59.95"
Measuring unit: 1/20 (0.05) seconds
Measuring mode: Elapsed time
Lap time (Memories: 5, Fastest lap memory)
Countdown Timer:
Measuring unit: 1 second
Input range: 1 to 60 minutes (1-minute increments)
Other: Elapsed time
Alarm: Daily alarm
Other: Power Saving
Power Supply: Solar panel and one rechargeable battery
Approximate battery operating time: 5 months (no exposure to light after a full
charge; 6 hours of stopped second hand, one signal reception of approximately
4 minutes per day)
E-105
Specifi cations
Accuracy at normal temperature: ± 15 seconds a month (with no signal calibration)
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, day
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 29 city codes and Coordinated
Universal Time); Daylight Saving Time (summer time) / Standard Time
Time Calibration Signal Reception: Auto receive up to six times a day (5 times a
day for the Chinese calibration signal; Remaining auto receives
cancelled as soon as one is successful); Manual receive
Receivable Time Calibration Signals:
Mainfl ingen, Germany (Call Sign: DCF77, Frequency: 77.5 kHz);
Anthorn, England (Call Sign: MSF, Frequency: 60.0 kHz); Fukushima,
Japan (Call Sign: JJY, Frequency: 40.0 kHz); Fukuoka/Saga, Japan
(Call Sign: JJY, Frequency: 60.0 kHz); Fort Collins, Colorado, the
United States (Call Sign: WWVB, Frequency: 60.0 kHz); Shangqiu City,
Henan Province, China (Call Sign: BPC, Frequency: 68.5 kHz)
E-104
Alarm
The alarm does not sound.■
Power may be low. Expose the watch to light until the
x
x
Second Hand starts moving
normally, at one-second intervals (page E-18).
The crown may be pulled out. Push the crown back in.
x
World Time
The indicated World Time is wrong.■
There is a problem with your Home City settings.
Check your Home City settings.
See “To confi gure Home City settings” (page E-45).
The indicated World Time is one hour off.■
The daylight saving time (summer time) setting for the World Time city is wrong.
See “To specify standard time or daylight saving time (DST) for a city” (page E-86).
E-103
■ Signal reception is being performed successfully, but the time and/or day is
wrong.
Possible Cause Remedy Page
Your Home City setting is wrong.
Check your Home City setting and correct
it, if necessary.
E-11
E-45
The watch may have been exposed
to magnetism or strong impact, which
has caused problems with proper
hand and day alignment.
Adjust the watch’s hand and day home
positions.
E-88
E-102
■ Auto Receive is not performed or I cannot perform Manual Receive.
Possible Cause Remedy Page
The watch is not in the Timekeeping
Mode.
Auto Receive will not be performed if the
watch is not in the Timekeeping Mode.
Push in and hold the crown for at least two
seconds to enter the Timekeeping Mode.
E-40
Your Home City setting is wrong.
Check your Home City setting and correct
it, if necessary.
E-11
E-45
A countdown timer operation is in
progress.
Both Auto Receive and Manual Receive
are impossible while a countdown is in
progress. In the Countdown Timer Mode,
stop the timer operation and then return to
the Timekeeping Mode.
E-73
There is not enough power for signal
reception.
Expose the watch to light to charge it. E-16
E-101
■ The current time setting changes after I set it manually.
You may have the watch confi gured for Auto Receive of the time calibration signal
(page E-32), which will cause the time to be adjusted automatically according to your
currently selected Home City. If this results in the wrong time setting, check your
Home City setting and correct it, if necessary (page E-45).
E-100
■ The
x
Second Hand indicates N (NO) when I check the result of the latest
receive operation.
Possible Cause Remedy Page
You are wearing or moving the x
watch, or performing a button
operation during the signal receive
operation.
The watch is in an area with poor
x
reception conditions.
Keep the watch in an area where reception
conditions are good while the signal receive
operation is being performed.
E-30
You are in an area where signal
reception is not possible for some
reason.
See “Approximate Reception Ranges”. E-27
The calibration signal is not being
transmitted for some reason.
Check the website of the organization x
that maintains the time calibration signal
in your area for information about its
down times.
Try again later.
x
—