Filter
Top Products
E-64
Looking up Sunrise and Sunset Times
You can use the Sunrise/Sunset Mode to look up the sunrise and sunset times for a particular date (year,
month, day) and location.
To enter the Sunrise/Sunset Mode
While in the Timekeeping Mode, press
D
to enter the Sunrise/Sunset
Mode.
• This will display the sunrise and sunset times for the current date
based the currently specifi ed city code, latitude, and longitude.
• Before trying to use the Sunrise/Sunset Mode, you need to confi gure
settings for the city code, longitude, and latitude for the location whose
sunrise and sunset times you want to view.
• The factory default confi guration of the location is: City Code:
TYO
(Tokyo); Latitude: North 35.7 degrees; Longitude: East 139.7 degrees.
Current date
Sunrise time
Sunset time
Current date
Sunrise time
Sunset time
E-65
To view the sunrise/sunset time for a particular date
1. Enter the Sunrise/Sunset Mode.
• This will display the sunrise and sunset times for the current
date at the location specifi ed by the city code, latitude, and
longitude.
2. While the sunrise/sunset time are on the display, use
A
(+) and
C
(–)
to scroll through the dates.
• Pressing one of the above buttons causes the month and day to
appear in the upper display area, and the year to appear in the
lower display area.
• When you release the button, the sunrise time of the selected day
will be shown in the middle display, while the sunset time will be
shown in the lower display.
• You can select any date between January 1, 2000 and December
31, 2099.
Note
•
If you think that the sunrise and/or sunset times are not correct for
some reason, check the watch’s city code, longitude and latitude
settings.
• The sunrise and sunset times displayed by this watch are times at
sea level. Sunrise and sunset times are different at altitudes other
than sea level.
Sunrise time
Sunset time
Date
Sunrise time
Sunset time
Date
E-66
To look up the sunrise and sunset times for a specifi c location
Important!
• You do not need to perform this procedure to look up the sunrise and sunset times in your currently
selected Home City.
• If you select a different city code to look up the sunrise and sunset times there, return to the city
code of your Home City (your current location) when you are fi nished. Otherwise, the time shown
in the Timekeeping Mode will not be correct.
• For information about the Home City setting, see “Confi guring Home City Settings” (page E-14).
1. In the Timekeeping Mode, hold down
E
for at least two seconds. First,
SET Hold
will fl ash on the
display, and
CITY
will be displayed in the upper display. After that, the currently selected city code and
city name will scroll across the upper display. Keep
E
depressed until the scrolling starts.
2. Use
A
(East) and
C
(West) to select the city code whose sunrise and sunset times you want to view.
• For details about city codes, see the “City Code Table” at the back of this manual.
• If this display shows the information you need, you can exit this procedure at this point by pressing
E
twice. If you want to specify a latitude and longitude for a more exact reading, advance to step 3,
below.
E-67
3. Press
E
to display the longitude/latitude setting screen, with the
latitude setting fl ashing.
4. Use
D
to move the fl ashing between the latitude and the longitude
setting.
5. Use
A
(+) and
C
(–) to change the fl ashing setting.
• You can configure the longitude and latitude setting within
following ranges.
Latitude Range: 65.0°S (South 65.0 degrees) to 0°N to 65.0°N
(North 65.0 degrees)
Longitude Range: 179.9°W (West 179.9 degrees) to 0°E to 180.0°E
(East 180.0 degrees)
• Latitude and longitude values are rounded off to the nearest
degree.
6. Press
E
to return to the Timekeeping Mode.
7. In the Timekeeping Mode, press
D
.
• Display the location whose sunrise and sunset times you want to
view.
Latitude
Longitude
PressD.
Latitude
Longitude
PressD.
E-68
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use
D
to select the Stopwatch Mode (
STW
) as shown on page E-10.
To perform an elapsed time operation
A
A
A A
C
Start Stop (Restart) (Stop) Reset
To pause at a split time
A
C
C A
C
Start Split
(
SPLIT
appears
in the upper part
of the display.)
Split release Stop Reset
Current time
Hours
Seconds
Minutes
1/10 second
Current time
Hours
Seconds
Minutes
1/10 second
E-69
To measure two fi nishes
A
C
A C
C
Start Split
First runner fi nishes.
(
SPLIT
appears in
the upper part of the
display.)
Displays time of fi rst
runner.
Stop
Second runner
fi nishes.
Split release
Displays time of
second runner.
Reset
Note
• The Stopwatch Mode can indicate elapsed time up to 999 hours, 59 minutes, 59.9 seconds.
• Once started, stopwatch timing continues until you press
A
to stop it, even if you exit the Stopwatch
Mode to another mode and even if timing reaches the stopwatch limit defi ned above. A paused timing
operation will remain paused until you press
A
to restart it or
C
to reset.
• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns
to elapsed time measurement.
• While
SPLIT
is shown in the upper display, it alternates with the hour digits of the split time at
one-second intervals.
E-70
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time, and sound an alarm when the end of the
countdown is reached.
To enter the Countdown Timer Mode
Use
D
to select the Countdown Timer Mode (
TMR
) as shown on page E-10.
• About one second after
TMR
appears on the display, the display will change to show the countdown
time hours.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting
down), press
A
to stop it and then press
C
to reset to the current
countdown start time.
• If a countdown is paused, press
C
to reset to the current
countdown start time.
2. Hold down
E
for at least two seconds.
• SET Hold will fl ash on the display and then the current start time
setting will start to fl ash. Keep
E
depressed until the start time
setting starts to fl ash.
3. Press
D
to move the fl ashing between the hour and minute settings.
4. Use
A
(+) and
C
(–) to change the fl ashing item.
• To set the starting value of the countdown time to 24 hours, set 0H 00’00.
5. Press
E
to exit the setting screen.
Countdown time
(Hour, minutes, seconds)
Current time
Countdown time
(Hour, minutes, seconds)
Current time
E-71
To perform a countdown timer operation
A
A
A A
C
Start Stop (Restart) (Stop) Reset
• Before starting a countdown timer operation, check to make sure that a countdown operation is not in
progress (indicated by the seconds counting down). If it is, press
A
to stop it and then
C
to reset to
the countdown start time.
• An alarm sounds for ten seconds when the end of the countdown is reached. This alarm will sound in
all modes. The countdown time is reset to its starting value automatically after the alarm stops
sounding.
To stop the alarm
Press any button.
Operation Guide 3439