Filter
Top Products
Operation Guide 2872
4
Altitude Records
Storing altitude data in memory creates an altitude record. If a reading is
greater than all of the other altitude readings currently stored in memory, it is
stored in the maximum altitude record. The following describes the contents
of each type of record.
Recording date (month, day), time (hour, minutes), altitude, and altitude
indicator: Up to 41 records
Maximum altitude (including recording date and time) and altitude indicator:
1 record
• The maximum altitude record shows information about the altitude record
that has the greatest altitude value. The maximum altitude record is
updated any time a reading produces an altitude that is greater than that of
the current maximum altitude record.
To store an altitude record in memory
In the Altimeter Mode, hold down D for about
one second until the watch beeps twice. This
indicates that a record of the altitude reading has
been stored in memory.
• You can recall data in memory using the Data
Recall Mode.
• Note that there is enough memory to store a
total of 41 records. If there are already 41
records in memory, storing another one
automatically deletes the oldest record to make
room for the new one.
To view altitude record data
1. Use C to enter the Data Recall Mode.
2. Press D to cycle through the altitude record screens in the sequence
shown below.
• The maximum altitude record appears first. After that, each press of D
scrolls through records in sequence, starting from the oldest record.
• If an error occurs while altitude data is being stored in memory or if there is
no altitude data in memory,
x
xxxx is shown for the measured altitude
value on the corresponding altitude record screen.
Maximum Data
Press D.
Oldest Data
Altitude
Recording date
(Month – Day)
Recording time
(Hour : Minutes)
▲
Newest Data
▲
▲
Altitude indicator
Deleting the Maximum Altitude Record Data
Use the following procedure when you want to delete the data in the
maximum altitude record. Note that you can delete maximum altitude record
data only. You cannot delete the data of any of the other altitude records.
To delete the maximum altitude record data
1. Use the procedure under “To view altitude record data” to display the
maximum altitude record.
• The maximum altitude record is the one with MAX next to the recording
time.
2. Hold down A until
x
xxxx appears in place of the maximum altitude
value. This indicates that the data is deleted.
Stopwatch
The stopwatch lets you measure elapsed time,
split times, and two finishes. Display of the minute
and seconds indicators can be turned on or off.
• The display range of the stopwatch is 9 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from
zero after it reaches its limit, until you stop it.
• The stopwatch measurement operation
continues even if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is
frozen on the display clears the split time and
returns to elapsed time measurement.
• All of the operations in this section are
performed in the Stopwatch Mode, which you
enter by pressing C.
Minutes
Seconds
1/100
second
Timekeeping
Mode time
Seconds indicator
Hours
Minute indicator
To measure times with the stopwatch
J
J
J
JJ
JJ J
JJ J
First runner
finishes.
Display time
of first runner.
Second runner
finishes.
J
Elapsed Time
EE E E A
Start Stop Re-start Stop Clear
Split Time
EA A E A
Start Split Split release Stop Clear
(
SPL
displayed)
Two Finishes
EA E A A
Start Split Stop Split release Clear
Display time of
second runner.
Minute and Seconds Indicators
The minute and seconds indicators graphically
indicate elapsed time values in the Stopwatch
Mode. The seconds indicator acts like the second
hand of an analog stopwatch, and moves on the
display to indicate the seconds count. The minute
indicator acts like the minute hand of an analog
stopwatch, and moves on the display to indicate
the minute count.
• You can use the following procedure to turn
display of the minute and seconds indicators
on and off.
Seconds
indicator
Minute
indicator
To turn display of the Stopwatch Mode minute and seconds
indicators on and off
1. With the Stopwatch Mode cleared to all zeros,
hold down A until the seconds indicator
starts flashing. This is the setting screen.
2. Press D to toggle display of the minute and
seconds indicators on (indicated when the
minute indicator is displayed) and off (minute
indicator not displayed).
3. When the setting is the way you want, press
A to exit the setting screen.
l
l
l
l
l
l
l
l
l
Seconds
indicator
Minute indicator
On
Off
Countdown Timer
You can set a countdown timer start time in the
range of one minute to 60 minutes. An alarm
sounds when the countdown reaches zero. An
auto-repeat feature causes the countdown to
restart automatically when the end of a
countdown is reached, and a progress beeper
signals the progress of the countdown.
• All of the operations in this section are
performed in the Countdown Timer Mode,
which you enter by pressing C.
Seconds
Minutes
Minute indicator
Seconds indicator
Timekeeping
Mode time
• Countdown start time
• Auto-repeat on/off
• Progress beeper on/off
• Minute, seconds indicator display on/off
Countdown start time
You can set a countdown start time in the range of one minute to 60 minutes,
in one-minute increments.
Auto-repeat
Whenever zero is reached, the watch beeps and auto-repeat automatically
restarts the countdown from the countdown start time you set. Turning off
auto-repeat causes the countdown to stop and the countdown start time to
appear on the display when the end of the countdown is reached.
Progress Beeper
When the progress beeper is turned on, the watch beeps at minute 10, 5, 4,
3, 2, and 1, of the countdown, and at second 50, 40, 30, 20, 10, 5, 4, 3, 2,
and 1 of the final minute of the countdown.
Minute and Seconds Indicators
The minute and seconds indicators graphically indicate the Countdown Timer
Mode minutes and seconds as they are counted down. You can turn display of
these indicators on or off.
Configuring the Countdown Timer
The following are the settings you should configure before actually using the
countdown timer.