Filter
Top Products
G B
3
O W N E R ' S M A N U A L
•
C A R D I O C O M F O R T PA C E R
equipment operates at either 230 V or 115 V
(North American version). NOTE! The equipment
must be connected to a grounded wall socket.
Do not use extension wires when connecting
the equipment to the power source. Always
switch off the power and unplug the equipment
from the electrical outlet immediately after
using!
To reduce the risk of burns, fire, electric shock or
injury to persons:
•
The equipment should never be left
unattended when plugged in. Unplug the
equipment from the outlet when not in use,
before carrying out any maintenance or repair
procedures, and before moving the unit.
•
Do not operate the equipment under a
blanket or other combustive material. Excessive
heating can occur and cause fire, electric shock
or injury to persons.
•
Do not connect the equipment to a power
source, or operate the equipment if there is any
sort of damage to the power cord or the unit
itself.
•
Do not connect the equipment to a power
source or operate the equipment outdoors or in
damp locations.
•
Keep the power cord away from hot objects.
•
Do not route the power cord beneath a carper
or place any objects on the cord. Also make sure
that the power cord does not run underneath
the equipment.
•
Do not alter (for example lengthen) the cord
between the transformer and the unit.
NOTE ABOUT ASSEMBLING
THE EQUIPMENT
Start by unpacking the equipment. The detailed
assembly instructions can be found at the back
of this guide. Follow the instructions in given
order.
Before assembly, check the contents of the
package. If a part is missing, please contact
your dealer with the model, equipment serial
no. and spare part no. of the missing part. You’ll
find a spare part list at the back of this guide.
The hardware kit contents are marked with *
in the spare parts list. The directions left, right,
front and back are defined as seen from the
exercising position. Keep the assembly tools,
as you may need them e.g. for adjusting the
equipment. Note that two people are needed
for the assembly.
The packaging includes a silicate bag for
absorbing moisture during storage and
transportation. Please dispose of the bag
once you have unpacked the equipment.
Allow at least 100 cm of clearance around the
equipment. We also recommend opening the
package and assembling the product on a
protective base.
SAVE THIS INSTRUCTION MANUAL!
ADJUSTMENTS
CORRECT EXERCISE POSITION
In order to find a suitable exercise position, you
can adjust the distance of the seat from the
pedals. Always make sure before beginning
exercising that your exercise position is correct.
Place your feet on the pedals.
Turn the seat adjustment knob anti-
clockwise and pull the knob outwards so
that the seat can be moved freely.
Push the seat to a suitable distance; the ball
of your foot should reach the pedal when
your leg is almost fully extended and when
the pedal is at its furthermost position from
the seat. Check the suitability of the distance
by pedalling anti-clockwise.
Release the knob when the distance is
correct; the seat will click into position.
Tighten the locking knob by turning it
clockwise.
You can select the inclination of the backrest to
uit your own preferences as follows:
Go behind the equipment.
Pull the backrest inclination adjustment
knob outwards so that the backrest can be
moved freely.
Select the desired inclination.
Release the knob when the inclination is
correct; the backrest will click into position.
NOTE! Always make sure that the locking knob is
properly fastened before starting to exercise!
HANDLEBAR SETUP
Loosen the locking screws on the front of the
handlebar support and find the right angle at
which to position the handlebar. Tighten the
locking screws.
1.
2.
3.
4.
5.
1.
2.
3.
4.
Cardio Comfort Pacer 2007_PUBLIS3 3 13.7.2007 11:01:36