2-4
Cisco 7600 Series Routers Module Guide
OL-9392-04
Chapter 2 Ethernet and Gigabit Ethernet Switching Modules
10/100 and 10/100/1000 Ethernet Switching Modules
24-Port 10BASE-FL Ethernet Switching Module (WS-X6024-10FL-MT)
The 24-port 10BASE-FL switching module (WS-X6024-10FL-MT) provides 24 switched, 10-Mbps,
full- or half-duplex ports. (See Figure 2-1.) The module has 24 MT-RJ connectors for connection to
multimode fiber-optic (MMF) cable.
The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t.
Note This module is a Class 1 laser product. Refer to the Regulatory Compliance and Safety Information for
the Cisco 7600 Series Routers for information on working with lasers.
Figure 2-1 24-Port 10BASE-FL Ethernet Switching Module (WS-X6024-10FL-MT)
The front panel LEDs are described in Table 2-3 on page 2-21.
48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148-GE-TX)
The 48-port 10/100/1000BASE-T switching module (WS-X6148-GE-TX) provides 48 switched,
10/100/1000-Mbps autosensing, full- or half-duplex ports. (See Figure 2-2.) The module has 48 RJ-45
connectors for use with either Category 3, Category 5, Category 5e, or Category 6 UTP cable. This
module can be upgraded with an inline-power daughter card to support IP phones.
Figure 2-2 48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148-GE-TX)
The front panel LEDs are described in Table 2-3 on page 2-21.
48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148V-GE-TX)
The 48-port 10/100/1000BASE-T switching module (WS-X6148V-GE-TX) provides 48 switched,
10/100/1000-Mbps autosensing, full- or half-duplex ports. (See Figure 2-3.) The module has 48 RJ-45
connectors for use with either Category 3, Category 5, Category 5e, or Category 6 UTP cable. The “V”
in the product number indicates that the inline-power daughter card is installed on the module. With the
voice daughter card installed, the module provides these IP phone features on each port:
• Inline power—Provides 48 VDC over standard Category 5, Category 5e, or Category 6 UTP cable
up to 328 feet (100 meters) from the switch to the IP phone. With inline power, pairs 2 and 3 (pins
1, 2, 3, and 6) of the four pairs in the cable are used to transmit power (6.3 W) from the switch. This
method of supplying power is sometimes called phantom power because the power signals travel
over the same two pairs used to transmit Ethernet signals. The power signals are completely
transparent to the Ethernet signals and do not interfere with their operation.
24 PORT 10FL
WS-X6024-10FL-MT
S
T
A
T
U
S
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
L
IN
K
26947
90851
WS-X6148V-GE-TX
STATUS
48 PORT 10/100/1000
BASE-T GE
SWITCHING MODULE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
PHONE
1
2
11
12
13
14
23
24
25
26
35
36
37
38
47
48
