A SERVICE OF

logo

Open as PDF
next previous
63 / 76 EN
Washing Machine / User’s Manual
2 Installation
RefertothenearestAuthorisedServiceAgentforinstallation
oftheproduct.Tomaketheproductreadyforuse,review
the information in the user manual and make sure that the
electricity,tapwatersupplyandwaterdrainagesystemsare
appropriatebeforecallingtheAuthorizedServiceAgent.If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparationofthelocationandelectrical,tapwaterand
wastewaterinstallationsattheplaceofinstallationis
under customer's responsibility.
B
WARNİNG: Installationandelectricalconnectionsof
the product must be carried out by the Authorized
ServiceAgent.Manufacturershallnotbeheldliablefor
damages that may arise from procedures carried out by
unauthorized persons.
A
WARNİNG: Priortoinstallation,visuallycheckiftheproduct
hasanydefectsonit.Ifso,donothaveitinstalled.
Damaged products cause risks for your safety.
C
Makesurethatthewaterinletanddischargehoses
aswellasthepowercablearenotfolded,pinchedor
crushedwhilepushingtheproductintoitsplaceafter
installation or cleaning procedures.
2.1 Appropriate installation location
• Placethemachineonarigidfloor.Donotplaceitona
long pile rug or similar surfaces.
• Totalweightofthewashingmachineandthedryer-with
fullload-whentheyareplacedontopofeachother
reachestoapprox.180kilograms.Placetheproduct
on a solid and flat floor that has sufficient load carrying
capacity!
• Donotplacetheproductonthepowercable.
• Donotinstalltheproductatplaceswheretemperature
mayfallbelow0ºC.
• Placetheproductatleast1cmawayfromtheedgesof
other furniture.
2.2 Removing packaging reinforcement
Tiltthemachinebackwardstoremovethepackaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
2.3 Removing the transportation locks
A
WARNİNG: Do not remove the transportation locks before
taking out the packaging reinforcement.
A
WARNİNG: Remove the transportation safety bolts before
operatingthewashingmachine!Otherwise,theproduct
willbedamaged.
1.Loosenalltheboltswithasuitablespanneruntilthey
rotate freely (C).
2. Remove transportation safety bolts by turning them
gently.
3. Attach the plastic covers supplied in the User Manual bag
into the holes on the rear panel. (P)
C
Keep the transportation safety bolts in a safe place to
reusewhenthewashingmachineneedstobemoved
again in the future.
C
Nevermovetheproductwithoutthetransportationsafety
boltsproperlyfixedinplace!
2.4 Connecting water supply
C
Thewatersupplypressurerequiredtoruntheproductis
between1to10bars(0.1–1MPa).Itisnecessaryto
have10–80litersofwaterflowingfromthefullyopen
tap in one minute to have your machine run smoothly.
Attachapressurereducingvalveifwaterpressureis
higher.
C
Ifyouaregoingtousethedoublewater-inletproduct
as a single (cold)water-inletunit,youmustinstallthe
suppliedstoppertothehotwatervalvebeforeoperating
theproduct.(Appliesfortheproductssuppliedwitha
blind stopper group.)
A
WARNİNG: Modelswithasinglewaterinletshouldnotbe
connectedtothehotwatertap.Insuchacasethelaundry
willgetdamagedortheproductwillswitchtoprotection
modeandwillnotoperate.
A
WARNİNG: Donotuseoldorusedwaterinlethosesonthe
newproduct.Itmaycausestainsonyourlaundry.
1.Connectthespecialhosessuppliedwiththeproductto
thewaterinletsontheproduct.Redhose(left)(max.90
ºC)isforhotwaterinlet,bluehose(right)(max.25ºC)is
forcoldwaterinlet.
A
WARNİNG: Ensurethatthecoldandhotwaterconnections
aremadecorrectlywheninstallingtheproduct.
Otherwise,yourlaundrywillcomeouthotattheendof
thewashingprocessandwearout.
2.Tightenallhosenutsbyhand.Neveruseatoolwhen
tightening the nuts.
3. Open the taps completely after making the hose
connectiontocheckforwaterleaksattheconnection