Filter
Top Products
7
4
STEP
Once the Treadmill is plugged in, you need to configure the Treadmill and perform an auto-calibration to assure maximum performance.
T9700S & T9700HRT CONSOLES:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the treadmill
on. A setup screen should appear on the console. Set your treadmill to the correct model number (9700S or 9700HRT) using the
ELEVATION arrow keys and the correct units (MI [miles]/ KM [kilometers]) using the SPEED arrow keys. If you are unsure of the model
number, you can locate the number on the front of the console. Once you have located the model number and units with the arrow
keys, press and hold SELECT. Now you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill perform this
complete function. “END” will appear when auto-calibration is complete. When auto-calibration is complete, it will take about 30
seconds for the treadmill to reboot and return to the start-up screen.
PREMIER CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the treadmill
on. A setup screen should appear on the console. Set your treadmill to the correct model number (9200, 9500, or 9600) using the
ELEVATION arrow keys and the correct units (MI [miles]/KM [kilometers]) using the SPEED arrow keys. If you are unsure of the model
number, you can locate the number on the console masts. Once you have located the model number and units with the arrow keys,
press and hold SELECT. Now you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill perform this
complete function. “END” will appear when auto-calibration is complete. When auto-calibration is complete, it will take about 30
seconds for the treadmill to reboot and return to the start-up screen.
DELUXE CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
You need to access Engineering Mode to configure and auto-calibrate your treadmill. With the safety key in place, please hold
down ELEVATION UP and SPEED DOWN for 5 seconds. “NONE” will appear in the data window. Press the UP arrow key until
“ENG 1” appears in the data window. Press SELECT. A number will appear in the speed window. Use the SPEED arrow keys to
select your treadmill configuration (“42”- T9500 MI [miles], “43”- T9500 KM [kilometers], “44”- T9600 MI, “45”- T9600 KM, “46”-
T9200 MI, “47”- T9200 KM). If you are unsure of the model number you can locate the number on the console masts. Press SELECT
to enter your configuration. “Update” will flash on the console. Press the ELEVATION UP arrows to P14 (Eng Out). Press STOP. Press
the UP arrow key to “ENG 4”. This is auto-calibration. Press SELECT.
To begin auto-calibration, press START. The treadmill will run through minimum and maximum speed and maximum incline. The auto-
calibration will take 3-5 minutes. Let the treadmill perform this complete function before exiting the Engineering Mode. “END” will
appear in the center window when the auto-calibration is complete. When auto-calibration is complete, it will take the treadmill about
30 seconds to go to 0 elevation and return to the start-up screen with P1 showing in the function window.
SIMPLE CONSOLE:
DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION
Once the treadmill is plugged in, you will need to configure and run auto-calibration. With the safety key in place, turn the treadmill
on. A setup screen should appear on the console. The large LED window displays the model number and the small LED window
displays the units. Set your treadmill to the correct model number (9200, 9500, or 9600) using the ELEVATION arrow keys and the
correct units (0 for miles and 1 for kilometers) using the SPEED arrow keys. If you are unsure of the model number, you can locate the
number on the console masts. Once you have located the model number and units with the arrow keys, press and hold SELECT. Now
you can perform auto-calibration by pressing START.
The treadmill will run through minimum and maximum speed and elevation. This will take 3 to 5 minutes. Let the treadmill perform this
complete function. “END” will appear in the window when auto-calibration is complete. When auto-calibration is complete, it will
take about 30 seconds for the treadmill to reboot and return to the start-up screen.
MODEL CONFIGURATION & AUTO-CALIBRATION