Filter
Top Products
B
VIEW BVIEW B
VIEW CVIEW C
C
Assembly
Guide
To avoid possible damage to this Folding Treadmill, please follow these assembly steps in the correct order.
Before proceeding though, find your new Folding Treadmill’s 2 serial numbers, located on the
front of the main frame and on the bottom of the console, and enter here:
Refer to these numbers when calling for service, and also enter these serial numbers on your Warranty Card
and in your own records. Be sure to read your Owner’s Guide before using your new Folding Treadmill.
If any parts, hardware or tools are missing, please call 1.800.335.4348
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Folding
Treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts
are in place and partially threaded in before completely tightening any ONE bolt.
1
STEP
• Slide lower console mast covers
over right and left console masts and
secure to frame using four flat head
bolts (M8x20L) on each side and two
button head bolts (M8x15L) and arc
washers (8.2x15x1.5T) on the back
of the console mast. Screw in all
hardware but DO NOT tighten.
PLEASE NOTE:
Right console mast
will have an access port for data
cable at the front of the console mast.
Be careful not to pinch data cable
when attaching right console mast to
frame.
ORANGE BAG
1
STEP
2
STEP
3
STEP
• Attach wire tie at center of console
mast support tube to data cable from
console and feed through support
tube opening to the right side of the
support tube.
• Attach console to support tube using
three long button head bolts (M8x60L),
lock washer (8.2x15.4x2.0T) and flat
washer (8.2x15x2.0T).
• Attach wire tie from top of right
console mast to data cable and feed
through console mast opening and
connect data cable to female data
cable connector.
PINK BAG
6
STEP
T9250 AND T9550
FOLDING TREADMILLS
6
STEP
• If the running belt slips when used,
use the supplied 8mm Allen wrench to
turn the left and right tension bolts
clockwise
1
/4-turn at a time until the
belt no longer slips.
• Run the treadmill at 2.0 mph. If the
running belt is too far to the
right
side,
use the supplied 8mm Allen wrench to
turn the
right
tension bolt
clockwise
1
/4-turn at a time until the belt remains
centered during use.If the running belt
is too far to the
left
side, turn the
left
tension bolt clockwise
1
/4-turn at a
time until the belt remains centered
during use.
BELT TENSION
5
STEP
Please refer to back cover for this
procedure, then return to Step 6.
AUTO-CALIBRATION
A
3
STEP
4
STEP
• Position upper console mast covers
over the console mast on each side and
match to outside covers. Secure with
three button head screws (M4x15L).
• Attach right and left side bottle
holders with two flat head bolts
(M5x15L) on top and two button head
bolts (M5x15L) and flat washers
(5.3x14x1.0T) on the bottom of each
bottle holder.
• Tighten all console mast hardware
at the base of each console mast.
• Position treadmill deck in upright
position by carefully lifting the back of
the treadmill until the latch engages.
Lock the transport wheels by pressing
the lower lever on lock. Secure the right
console mast cover with two flat head
bolts (M4x15L) for the front of the cover
and one flat head pointed screw
(M4x15L) for the rear of the cover.
• Repeat on left side.
• Unfold the treadmill.
GREEN BAG
4
STEP
Frame Serial Number
Console Serial Number
B
VIEW B
VIEW B
VIEW C
C
VIEW A
VIEW A
2
STEP
•
Attach right and left handlebars to
console masts with two button head bolts
(M8x15L), lock washer (8.2x15.4x2.0T)
and flat washer (8.2x15x1.4T) on the
sides of the handlebar and two flat head
bolts (M8x15L) and arc washers on the
underside of the handlebar.
• Slide right and left console mast
covers over support tube.
• Attach support tube to console
masts and secure with two button
head bolts (M8x20L), lock washers
(8.2x15.4x2.0T), and flat washers
(8.2x15x1.4T) on each side. Make
sure all four bolts are screwed in
before tightening any of the bolts.
BLUE BAG