Filter
Top Products
3
STEP
4
STEP
5
STEP
1
STEP
Suspension Arm
2
STEP
2
STEP
• Lift the left incline arm and insert the
bearing end of the suspension arm into
the
bracket of the incline arm. From the
outside,
insert a hex head bolt
(M12x95L)
through the bracket and suspension arm.
Secure with a lock washer (M12) and
nut (M12). Tighten with two 19mm
wrenches. Make sure hardware is tight.
• Repeat this step on the right side.
BLUE BAG
3
STEP
NOTE:
A second person will be helpful
to complete this step.
• Place the left connection arm over the
left incline arm bracket and connect
with two socket head cap bolts
(M10x65L). Tighten only a few turns
with the 8mm L-shaped wrench.
• Insert the pin on the front flange of
the connection arm to the hole in the
console mast elevation bracket.
• Repeat these steps on the right side.
• When the pins of both connection
arms are seated in the holes of the
console mast elevation bracket lift the
entire assembly slightly to line up the
screw holes. Insert four socket head
cap bolts (M8x30L) with washers
(8.2x13x1.4T) through these holes.
Secure with a washer (8.2x13x1.4T)
and nylon nut (M8) to each bolt.
Tighten with the 6mm L-shaped
wrench and 13mm wrench.
• Go back and completely tighten the
screws that connect the connection
arms to the incline arms with the 8mm
L-shaped wrench.
PINK BAG
1
STEP
NOTE:
A second person will be helpful
to complete this step.
• Slide the console mast boot onto the
console mast.
• Locate the data cable and elevation
motor connector in the main frame
recess. Make sure they are pulled out of
the opening and can be easily plugged
in when the mast is inserted.
• Set the console mast into the con-
sole mast frame bracket. Secure the
front of the mast to the frame bracket
with four socket head bolts (M8x20L),
four lock washers (M8), and four flat
washers (8.2x16x1.4T). Tighten with
the 6mm T-shaped wrench. Secure the
sides of the console mast to the console
mast bracket with one flat head bolt
(M8x12L) to each side. Tighten with
the 5mm L-shaped wrench.
• Plug in the elevation motor cable to
the cable socket sitting in the frame
bracket.
• Wrap the wire tie that comes out of
the bottom of the console mast around
the data cable that exits the top of the
frame. Feed the wire tie and data cable
up through the channel in the side of the
mast while pulling the wire tie straight
up through the top of the mast.
• Slide the boot down over the frame
and snap in place.
ORANGE BAG
5
STEP
• Remove the wire tie from the data
cable and console mast.
• With the screwdriver, remove the
five bolts from the rear console cover.
Place the cover and five bolts aside.
• Remove the four console mounting
bolts and one grounding bolt from the
backside of the console with the
screwdriver. Connect the heart rate
wires coming from the mast to the
heart rate wires coming from the
bottom of the console. Insert the data
cable through the bottom of the console
and plug into the board. Pull any extra
wire down into the console mast.
Secure console to the bracket using the
four console mounting bolts removed
earlier. Tighten with the screwdriver.
• Insert the grounding bolt to the back
side of the console and tighten with the
screwdriver. Do not over tighten.
• Position the rear console cover on
the back of the console and secure
with the five bolts removed earlier.
Tighten with the screwdriver.
• Position the covers over the rear
incline arm bracket and secure each
cover in place with four bolts (M5x25L).
• Position the cover over the elevation
bracket and secure with two bolts
(M5x15L).
• Take the rear base frame covers and
pull apart to separate and slide around
the bottom of the incline arm. Snap the
three tabs down to set in place.
• Plug the power cord into the power
socket in the front of the unit. Plug the
other end of the cord into the wall outlet.
Make sure the power switches at the
bottom of the unit and on the back of
the console are in the on position.
BLACK BAG
4
STEP
• Place the left dual-action arm on the
left rotation housing and secure in
place with four bolts (M8x20L) and
lock washers (M8). Tighten with the
6mm L-shaped wrench.
• Line up the rotation housing cover
over the rotation housing and push to
snap in place.
• Insert a bushing onto each side of
the link arm bracket. Slide the link arm
between the flanges of the dual-action
arm bracket. Insert a socket head cap
bolt (M6x50L) through the hole to
connect the brackets. Secure with a
washer (6.4x11x1.5T) and nylon nut
(M6). Tighten with the 10mm wrench
and 5mm L-shaped wrench.
• Set the dual-action cover in place
over the connection bracket. Place the
nut (M5) into the recess on the inside
cover. Insert a bolt (M5x50L) through
the outside hole and tighten to the nut
with a screwdriver.
• Repeat these steps on the right side.
GREEN BAG
Incline Arm
Connection Arm
Connection
Arm Pin
Rotation Housing
Dual-Action Arm
Link Arm Bracket
Rear Base
Frame Covers
Incline Arm
Covers
Elevation
Bracket Cover
Console
Console
Cover
Data Cable
Wire Tie
Elevation Motor
Cable
Elevation Motor
Connector
Grounding
Bolt