Vector VEC1198POB Camping Equipment User Manual


  Open as PDF
of 6
 
5
OPERATING THE LED BACKUP LIGHT
The LED Backup Light in the lantern base is controlled by the LED Light ON/OFF
Pushbutton on the back of the unit. (See the “Control and Function Guide” on page 2.)
USING THE 12 VOLT DC PORTABLE POWER SUPPLY
This portable power source is also for use with 12 volt DC accessories equipped with
a male accessory outlet plug that are rated up to 1 amp (generally, a cell phone
charger).
1. Lift up the cover of the unit ‘s 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 Volt DC Accessory
Outlet on the side of the unit (see the “Control and Function Guide” on page 2).
DO NOT EXCEED A 1 AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically press the battery charge level pushbutton to check battery status.
CARE AND MAINTENANCE
Cleaning
Over time, dust or fingerprints may accummulate on the Lantern glass. Clean with a
soft, clean, oil-free cloth moistened with household window cleaner. Do not use
alcohol based cleaners on plastic surfaces. This will eventually cause surface clouding.
Note: Never submerge this unit in water or any other liquid.
Replacement Parts
Check unit periodically and discontinue use if parts or accessories are found to be
damaged or defective. To replace worn or defective parts, contact Vector Customer
Service toll-free at (866) 584-5504.
12 Volt DC Adapter Plug Fuse Replacement
The fuse in the DC plug protects the charging circuit of the 12 Volt DC Adapter. If AC
powering/recharging works, but DC powering/recharging does not, then the fuse
may be opened (blown).
To replace the fuse:
1. Unscrew the gold end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate replacement fuse with same type and rating.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 Volt DC Adapter.
4
Using the Dynamo Hand-Crank
Collapse the Hanging Hook and Handle to release the hand-crank and press it
against the unit’s body to secure into position. Rotate the Dynamo Hand-Crank handle
clockwise (at a rate of approximately 1.6 rotations per second) to generate power if
back-up battery power is low. Turn off all functions while recharging using this method
for best results.
Using Battery Power
The VEC1198POB comes with a 12 Volt DC Detachable Battery Pack that can power
all of the unit’s features. When the Removable Battery will no longer hold a charge,
it can be replaced. See “Battery Replacement/ Disposal” on page 5.
Note: When the battery is inserted into the unit and the AC plug pin is inserted into
the charging port, (even if the cube is not plugged in) the Removable Battery
will charge the Internal Backup System Battery.
OPERATING THE LANTERN
The Lantern is controlled by the Lantern ON/OFF Pushbutton on the back of the unit
(see the “Control and Function Guide” on page 2).
Note: When the 12 Volt DC detachable Battery Pack power runs low and alternate
12 Volt DC power cord use is unavailable, the tube Lantern will power off. The
Radio and LED Backup Lights will continue to operate as long as Hand Crank
backup battery source is utilized.
OPERATING THE AM/FM RADIO
See the “Control and Function Guide” on page 2 to locate referenced controls, knobs
and selectors.
• Slide the AM/FM/WX Selector to the desired frequency (the AM or FM position).
• Turn the Radio Tuner Knob to select the desired station.
• Extend the built-in Radio Antenna and adjust for best reception.
• Adjust the volume using the Volume Control Knob.
• To turn the Radio OFF, simply slide the AM/FM/WX Selector to the OFF position.
OPERA
TING THE WEATHER RADIO
• Slide the AM/FM/WX Selector to the WX (Weather Band) position.
• With the ALERT ON/OFF Pushbutton OFF, turn the Radio Tuner Knob to select the
NOAA station with the strongest signal.
• Extend the built-in Radio Antenna and adjust for best reception.
• Adjust the volume using the Volume Control Knob.
• Press the Alert Pushbutton to turn the Alert feature ON (the Alert LED will light) and
press the ALARM/LOCK Pushbutton to set it in LOCK position (the Alarm Lock LED
will light) for Alert standby mode. Note that the speaker is muted while Radio
monitors for a hazard alert.
• To turn the Radio OFF, simply slide the AM/FM/WX Selector to the OFF position.
Notes: While in ALERT mode, the hazard alarm will sound briefly when a hazard alert
is received. While in the LOCK position, the alarm SOUNDS CONTINUOUSLY
WHEN THE HAZARD ALERT IS RECEIVED UNTIL THE USER TURNS IT OFF.
For the Lock Function to be available, ALERT must be engaged.
VEC1198POB_Manual_022406 2/24/06 5:21 PM Page 4
 previous