Filter
Top Products
6
OWNER'S MANUAL • T4F/T5F
This information is needed for estimating energy
consumption.
2. Set the age of the user. Use the arrow keys to
change the setting, and press Enter to confi rm your
selection. You will then move to the next setting.
This information is needed for estimating energy
consumption.
3. Set the measurement units (Metric = metric
system, Imperial = avoirdupois). Use the arrow
keys to change the setting, and press Enter to
confi rm your selection. You will then move to the
next setting.
4. Set the audio signal (ON = signals on, OFF
= signals off). Use the arrow keys to change the
setting, and press Enter to confi rm your selection.
You will then move to the next setting.
5. The TOTAL TIME display shows the total usage
time period of the treadmill. The value cannot be
changed. Press Enter to move to the next display.
6. The TOTAL DISTANCE display shows the total
distance run on the treadmill. The value cannot be
changed. Press Enter to return to gender setting or
press Start to exit user settings.
CHOOSING AN EXERCISE
To switch on the power to the treadmill, connect
the power cord between the connector at the front
of the treadmill and a wall socket, and then press
the power switch to the on position. The switch
will light up. Make sure that the safety tether key is
in place. Press Select until the signal light indicates
the desired exercise. You can choose between:
1. Manual exercise in which you adjust both speed
and elevation yourself during the exercise.
2. Heart rate controlled HRC exercise in which
the treadmill adjusts the speed / elevation
automatically, so that your heart rate stays at the
level set. You always need to wear a heart rate belt
while doing HRC exercises.
3. Preset exercise profi le in which speed/elevation
or heart rate level vary according to the preset
program.
MANUAL EXERCISE
1. Manual exercise is the treadmill default setting.
2. Press Enter and set the user weight with the
arrow keys. Press Enter to confi rm your setting.
The setting will remain in the meter's memory
until replaced with a new one.
3. Press Start. The belt starts moving at 1.0 km/h /
0,6 mph. Use the Hare/Tortoise keys to adjust the
speed and the elevation control keys to adjust the
elevation.
4. Press Stop/Pause and the treadmill stops and
moves into waiting state for 5 minutes. You can
restart the interrupted exercise by pressing the Start
key within 5 minutes. Press Stop/Pause twice to
end your exercise. Keep the Stop key pressed down
for 2 seconds to reset the meter. The meter then
switches to its initial state.
If the user weight does not need to be adjusted,
you can start the exercise directly by pressing the
Start key. The profi le display collects the exercise
speed details at one minute intervals. After 16
minutes, the display will shift to the left to show
the speed details from the last 16 minutes.
HEART RATE CONTROLLED EXERCISE
1. Heart rate controlled exercises always require the
use of a heart rate belt. If heart rate measurement
is not working correctly, the error message HR
ERROR will be displayed. You should then
make sure that you have properly followed the
instructions on the use of the heart rate belt.
2. Press Select until the signal light shows next to
the HRC text.
3. Press Enter to move to the heart rate exercise
setting. The latest heart rate exercise value is shown
on the display in the middle. You can adjust the
value with the Hare/Tortoise keys. Press Enter to
confi rm your setting. The setting will remain in the
meter's memory until replaced with a new one.
4. Press Enter and set the user weight with the
Hare/Tortoise keys. Press Enter again to confi rm
your selection. That setting will remain in the
meter's memory until it is replaced with a new one.
5. Press Start. The exercise begins and the belt
starts moving.
6. If the set heart rate value seems too strenuous
or easy, change the heart rate value by using the
Hare/Tortoise keys.
7. Press Stop/Pause and the treadmill stops and
moves into waiting start for 5 minutes. You can
restart the interrupted exercise by pressing the Start
key within 5 minutes. Press Stop/Pause twice to
end your exercise. Keep the Stop key pressed down
for 2 seconds to reset the meter. The meter then
switches to its initial state.
If the exercise heart rate and user weight do not
need to be adjusted, select HRC mode and press
Start to begin heart rate controlled exercise. The
profi le display collects the heart rate details of the
exercise at one minute intervals. After 16 minutes,
the display will shift to the left to show the heart
rate details from the last 16 minutes.
EXERCISE PROFILES
Tunturi has developed different preset exercise
profi les in order to ensure versatile, pleasant and
goal-oriented training.
The shape of the different
profi les is shown in the back fold and on the key
panel
of the meter, and the meter also provides
more detailed information about the selected
profi le during the exercise. The meter gives an
audio signal in advance of changes in a profi le. The
TUNTURI_J4F_J5F 6 10.9.2004, 13:22:22