Filter
Top Products
hold
hold
Increase
Decrease
Increase
faster
Decrease
faster
[ST/STP]
[ST/STP]
[LAP/RESET]
[LAP/RESET]
[MODE]
[MODE]
[MODE]
[MODE]
minute
hour
hold
Dual Time Mode
1 minute
compass
direction
dist indicator
direction of travel heading indicator
compass
bearing
any button
except [LIGHT]
Compass Mode
Compass Stand-by Mode
magnetic north
true north
magnetic
declination
magnetic
declination
hold
[LAP/RESET]
[MODE]
[MODE]
[MODE]
1 minute
Compass
Mode
Declination
Mode
Calibration
Mode
Rotation
Start
Finish
S
W
E
N
DUAL TIME MODE
To Set the Dual Time Mode
• In Dual Time Mode, Press and
Hold [ MODE ] for 2 seconds
until the "minutes" digits flash
• Press [ MODE ] to navigate to
the setting that you wish to
change. See navigation chart at
right
• When the setting you wish to
change flashes, Press [ ST/STP ]
to raise the value or [LAP/RESET]
to lower the value.
Note: If you Press and Hold the
button, the rate of change is
faster
• When the hour is set, Press
[ MODE ] to confirm and return to
the Dual Time Mode
NOTE: If NO INPUT for 1 minute
during the setup, the display will
default to the Dual Time Mode
COMPASS MODE
This watch is a digital compass that provides directions, bearings and
Magnetic North Pole location.
Caution: Accurate readings will be compromised when used near
magnetic fields, mobile phones, speakers, motors, electrical
appliances and inside a moving vehicle or a ferroconcrete building.
Watch may need to be calibrated for
declination
Perform calibration when:
• first time of use
•
DIST
is flashing
• Declination has changed
• Battery has been changed
Compass Display
To access, press [ LAP/RESET ] when in
current time mode.
• Compass direction - displays in 1st
row
• Compass bearing - displays in 2nd row
• Animated cardinal points - display in
perimeter bar graph
Compass Standby Mode
• To extend battery life, watch will
switch to standby mode if there is NO
INPUT for 1 minute when in compass
mode
• Press any button except [ LIGHT ] to
exit standby mode
COMPASS CALIBRATION
To Calibrate the Compass
• In the Compass Mode, Press
and Hold [ MODE ] for 2
seconds. DEC will display in
the 1st row and the digits will
flash
• Press [ ST/STP ] to set
desired declination angle (-90
to +90)
• Press [ MODE ] CAL will
display in the 1st row and the
north pole pointer will move
• Lay the watch on a level
surface. Steadily rotate the
watch counter-clockwise
twice. Keep the pointer in the
same direction through out
the rotation
• Press [MODE] to confirm and
return to Compass Mode
on the continent. Where True and Magnetic North are in the same direction, the
declination is zero. At any point west of that line, your compass needle will
point east of True North. This is called “Easterly Declination.” At any point east
of that zero line, your compass needle will point west of True North. This is
called “Westerly Declination.”
NOTE: The watch displays Westerly Declination as a negative number.
example: -45
MAGNETIC DECLINATION
The Magnetic sensor in the compass is
attracted by the magnetism of the
Earth and therefore, always points to
the constantly shifting Magnetic
North. There is another “North Pole.”
True North is static and located
geographically about 800 miles
north of the magnetic pole. Maps
and directions usually are based on
True North. Magnetic declination is
the angle between True North and
Magnetic North. The amount of
declination at any given point
depends on the location of that
point.
MAGNETIC DECLINATION COMPENSATION
The watch will automatically make declination compensation. We have
included a list of the declination angles of North America. In the
Declination Setting Mode, input the closest angle and the watch will
make the adjustment.