Filter
Top Products
- two 3/8" NYLOCK NUTS
14.
Attach item (16) BOOM to item (I4)
REAR UPRIGHT using:
- two 1/’2" X 3" BOLTS
- three 1/2" FLAT WASHERS
- one 1/2" LOCK WASHER
- one 1/2" LOW HT NYLOCK NLrr
I5. Attach item (11) LEG CU’RL/EXT
item (8) M.~I’N UPRIGHT using:
- one 1/2" X 3" BOLT
- one I/2" LOW HT NY’LOCK ~
- two 1/2" ID FLANGE BEARINGS
I 6. Attach item (19) HEAD PLATE to item
(20) SELECT SH_-YFT using:
- one 3/8" X 1-I/2" BOLT
- one 3/8" LOCK WASHER
- one 3,;8" FLAT WASHER
17. InstaIi t~vo PLATE BUSH’~’GS into
each of fine fifteen WEIGHT PLATES.
18. Place v,vo \~,~IGHT STACK
CUSHIONS oyez large holes in item
(!0) BASE.
I9. Inserz each of ~e ~’o GUIDE RODS
through the W’EIGHT STACK
CUSHIONS ~’~d into the l~"ge holes in
item (10) BASE.
20.
Slide each of the fifteen V,-EIGHT
PLA.TES over the GUIDE RODS ’~ith
pin hole facing towards fine ~-ont oft.he
machine.
21.
Slide the HEAD PLATE ASSENfBLY
over the G_.ID,_ RODS.
to the WEIGHT PLATES.
24. Attach two 3-I/2" OD PULLEYS to two
item (1) PLATES using:
- two 3/8" X 2-1/4" FIOLTS
- four 318" FLAT WASHERS
- two 318" NYLOCK NUTS
25. Route threaded end of 651340I CABLE
ASSEMBLY as follows:
- into front slot of item (16) BOOM.
- out uh.rough back stct of item (16)
BOOM.
- between two 3:1/2" OD PULLEYS on
PU’LLEY/PLATE ASSEMBLY.
- into first large hole i:a bottom of item
(I 6) BOOM.
- out t~ough second h~ge hole in
bet:ore of item (16) BOOM.
- d~-ead end of CA.BLF into top of
SELECT STEM.
26. Route end of 6513301 CABLE
AS SEMBLY with sma!I black nyton b~l
as :’o!!ows:
- ::~-ough slot of item (i I) LEG
C L~:~,,’EXTENSION.
-
"d~-ough bomom sIot of i~e..’m, (8) ~LA_rN
- be~veen t:wo 3-1/2" OD PULLEYS on
PLZLEY:PLATE ASS EMBLY.
- d-.~-ough middle slot of item ($) ,"vLZl’N
UP~GH-T.
.a.,-.~.:h ~.e following components to
~-, ~GHI:
- one 3-1 2" OD PULLEY
- 7ao FLA2’;GE SPACET~
- r.va 3,8" X ~-3,~" BOLTS
-
\V ’, q"
:-.v: 3,~" FLAT ~ .-._r.=~,.~
22. Poshion the GUIDE RODS ,-,--’haler item
- ,".vo 3.8" NYT_OCK ,",’UTS
(8) .MA_rN-UPRAGHT .~..~d hold. in-place ...................................
using two GUIDE ROD PENS.
28. A.’:ech Che follov,
4-.o.
.,,__ co~nponent.s to item
¢’: Y; LEG CUP,.L.’EXTE:¢SION:
23. Apply the WEIGHT STACK LABELS
- or.e : 1.2" OD PULLEY
PART # 6519.-0! 5
REVISION 06/£’~/..’96