Linear HCI+2 Bicycle Accessories User Manual


  Open as PDF
of 2
 
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,I-RAIL,EXTENTION,2 FT - LINEAR P/N: 228232 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 17.000” X 11.000” - SCALE: 1-1 - SIDE 2 OF 2
12. INSTALL FINAL BOLT 13. REPOSITION THE TROLLEY STOP BOLT 14. TIGHTEN ALL BOLTS 15. REMOVE CHAIN FROM TURNBUCKLE
16. ADD SHORT CHAINS TO TURNBUCKLE 17. REASSEMBLE TURNBUCKLE 18. REINSTALL SPROCKET 19. SET TROLLEY POSITION
20. ADJUST SPROCKET POSITION 21. ADJUST CHAIN TENSION 22. TIGHTEN TURNBUCKLE LOCKNUTS LIMITED WARRANTY
This product is warranted to the original consumer against defects in material and workmanship for
fi ve (5) years. Linear will repair, or at its option, replace, any device that it fi nds requires service under
this warranty, and will return the repaired or replaced device to the consumer at Linear’s cost. Devices
must be sent to Linear for service at owner’s expense. This warranty does not apply to damage to
the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear or due
to failure to follow Seller’s instructions, or arising from improper installation, storage or maintenance.
In no event will Linear be responsible for incidental, compensatory, punitive, consequential, indirect,
special or other damages. The remedies provided by this warranty are exclusive. Some states do not
allow the exclusion or limitation of incidental and consequential damages, so the above limitation
or exclusion may not apply to you. Any warranties implied by law are limited to the time periods set
forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specifi c legal rights, and you may also have
other rights which vary from state to state.
For warranty service and shipping instructions contact Linear at the phone number shown below. In
order to be protected by this warranty, save your proof of purchase and send a copy with equipment
should repair be required. All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.
SLIP THE SPROCKET HOLDER
ONTO THE END OF THE
EXTENSION RAIL
SET THE TROLLEY DISTANCE
FROM THE PULLEY BRACKET
4 TO 6 INCHES
THE TROLLEY MUST REST 4 TO 6 INCHES
FROM THE PULLEY BRACKET TO MATCH
THE PRE-SET LIMITS IN THE OPERATOR
ADD THE TWO SHORT EXTENSION CHAINS
TO EACH END OF THE STOCK CHAIN
CONNECT THE TWO EXTENSION CHAINS
TO THE TURNBUCKLE EYE-BOLTS USING
THE MASTER LINKS SUPPLIED
NOTE: ONE SIDE OF THE
TURNBUCKLE IS LEFT-HAND
THREAD, THE OTHER SIDE
IS RIGHT-HAND THREAD
REASSEMBLE THE
TURNBUCKLE AFTER
ADDING THE EXTENSION
CHAINS
BE SURE TO TIGHTEN ALL
THE BOLTS ON THE EXTENSION
RAIL ASSEMBLY
REMOVE THE MASTER LINK AND
DISCONNECT THE CHAIN FROM EACH
OF THE TURNBUCKLE EYE-BOLTS
BE SURE TO KEEP THE MASTER LINKS!
THEY WILL BE USED AGAIN
INSTALL THE LAST BOLT
AND NUT INTO THE END SLOT
USE ONE OF THE SHORTER
1/4-20 x 5/8" BOLT AND KEPS NUT
LEFT OVER FROM THE DISASSEMBLY
DONE IN STEP 5
REMOVE THE TROLEY
STOP BOLT AND NUT
FROM THE STOCK I-RAIL
MOVE THE TROLLEY STOP BOLT
AND NUT TO THE BOTTOM
SECTION OF THE EXTENSION RAIL
BOTTOM RAIL SECTION
(TOP VIEW)
STOP BOLT HOLE
HOLD SCREWDRIVER IN
TURNBUCKLE SLOT
TIGHTEN THE TWO
TURNBUCKLE
LOCKING NUTS
NOTE: ONE SIDE OF THE
TURNBUCKLE IS LEFT-HAND
THREAD, THE OTHER SIDE
IS RIGHT-HAND THREAD
ALIGN FLAT ON SPROCKET
THIS DIRECTION TO MATCH
FLAT ON OPERATOR SHAFT
BE SURE TO KEEP THE TROLLEY
AT 4-6 INCHES FROM THE PULLEY
BRACKET AS SHOWN IN STEP 19
ADJUST THE CHAIN
TENSION WITH THE
TURNBUCKLE
THE CENTER OF THE CHAIN SHOULD BE
SLIGHTLY ABOVE (NO MORE THAN 1/8")
THE BOTTOM EDGE OF THE RAIL
Copyright © 2008 Linear LLC 228232 A
 previous