Filter
Top Products
ASSEMBLING THE UPRIGHT EXERCISE BIKE
Tools Required: Metric Wrench Set, Metric Allen
Wrench Set, Phillips Screwdriver
1. Locate and install the two LEVELER FEET (A) to the
bottom of the REAR STABILIZER (B).
2. Attach the REAR STABILIZER (B) to the BASE UNIT
(C) using two 2-3/8" BUTTON HEAD SCREWS (1)
from the top of the REAR STABILIZER BRACKET (D)
and two 13/16" BUTTON HEAD SCREWS (2) from the
front side of the REAR STABILIZER BRACKET.
Tighten the SCREWS securely.
3. Locate the MONOCOLUMN (E). Insert the WIRE (F)
leading from the SIDE ACCESS HOLE (G) of the
MONOCOLUMN fully into the MONOCOLUMN.
Remove the GROMMET (H) from the SIDE ACCESS
HOLE and set it aside.
4. Slide the MONOCOLUMN COVER (J) onto the
MONOCOLUMN (E) as shown. Slide the MONOCOL-
UMN COVER up to the HANDLEBAR TUBE (K).
5. Re-insert the GROMMET (H) into the SIDE ACCESS
HOLE (G) of the MONOCOLUMN (E). Pull the WIRE
(F) back out through the SIDE ACCESS HOLE.
6. With the HANDLEBAR TUBE (K) facing the rear of the
unit as shown, slide the MONOCOLUMN (E) into the
MONOCOLUMN BRACKET (L) of the BASE UNIT (C).
Slide the MONOCOLUMN down until it is fully seated.
Secure the MONOCOLUMN to the MONOCOLUMN
BRACKET using two 3-15/16" HEX HEAD BOLTS (3)
and three LOCK WASHERS (4) (as shown) from the
rear side of the MONOCOLUMN and two 2-3/8" HEX
HEAD BOLTS (5) and LOCK WASHERS (4) from the
user left side of the MONOCOLUMN BRACKET.
Tighten the BOLTS securely.
CAUTION: BE CAREFUL NOT TO PINCH THE
WIRE (M) LEADING FROM THE MONOCOLUMN
BRACKET (L) WHEN INSERTING THE MONO-
COLUMN (E) INTO THE MONOCOLUMN
BRACKET.
7. Connect the WIRE (M) leading from the MONOCOL-
UMN BRACKET (L) to the corresponding WIRE (F)
from the SIDE ACCESS HOLE (G) of the MONOCOL-
UMN (E). Slide the MONOCOLUMN COVER (J)
downward to the meet the MAIN SHROUDS (N).
Secure the MONOCOLUMN COVER to the MAIN
SHROUDS using four 1/2" PHILLIPS SCREWS (6)
and matching FLAT WASHERS (7). Tighten the
SCREWS securely. Do not overtighten the SCREWS.
8. Locate the SEAT POST CAP (O). With the curved side
facing upward toward the SEAT (P), slide the SEAT
POST CAP over the SEAT POST (Q).
9. Locate and slide the SEAT POST SPACER (R) over
the end of the SEAT POST (Q). Using two 1/4"
PHILLIPS SCREWS (8), secure the SEAT POST
SPACER to the end of the SEAT POST. Tighten the
SCREWS securely.
10. With the nose of the SEAT (P) facing forward, insert
the SEAT POST (Q) into the SEAT POST SUPPORT
(S).
11. Begin inserting the SEAT ADJUSTMENT KNOB (T).
Lift upward on the seat and seat post until the seat
post locks into a position. Insert the 5/16" PHILLIPS
LOCKING SCREW (9) and tighten securely.
12. Slide the SEAT POST CAP (O) downward to meet the
top of the SEAT POST SUPPORT (S). Secure the
SEAT POST CAP to the SEAT POST SUPPORT using
two 1/2" PHILLIPS SCREWS (6). Tighten the
SCREWS securely. Do not overtighten the SCREWS.
13. Remove the DISPLAY CONSOLE (U) from its shipping
carton. Position the above the DISPLAY CONSOLE
BRACKET (V). Connect the CONNECTOR (W) lead-
ing from the DISPLAY CONSOLE BRACKET to the
corresponding jack located on the back of the DIS-
PLAY CONSOLE. Secure the DISPLAY CONSOLE to
the DISPLAY CONSOLE BRACKET using four 1/2"
PHILLIPS SCREWS (6). Tighten the SCREWS
securely. Do not overtighten the SCREWS.
14. Locate the HANDLEBAR ASSEMBLY (X). With the
handlebars facing forward, position the HANDLEBAR
ASSEMBLY near the top of the HANDLEBAR TUBE
(K). Slide the HANDLEBAR ASSEMBLY fully into the
HANDLEBAR TUBE. Secure the HANDLEBAR
ASSEMBLY to the HANDLEBAR TUBE using four 5/8"
BUTTON HEAD SCREWS (10) and matching FLAT
WASHERS (11). Tighten the SCREWS securely.
15. Locate the PEDALS. Install the RIGHT PEDAL (Y)
(marked with an "R") to the USER RIGHT CRANK
ARM (Z). Repeat for the LEFT PEDAL (AA) (marked
with an "L").
NOTE: THE LEFT PEDAL (Y) HAS REVERSE
THREADS.
16. Locate the WATER BOTTLE BRACKET (BB). Secure
the WATER BOTTLE BRACKET to the underside of
the HANDLEBAR TUBE (K) using two 3/8" PHILLIPS
SCREWS (12). Tighten the screws securely. Insert the
WATER BOTTLE (CC) into the WATER BOTTLE
BRACKET.
17. Position the unit in the desired location for use. The
unit can be easily moved into place by lifting the rear
of the unit and rolling it on the front rollers. Level the
unit before use. Refer to the leveling instructions stat-
ed in the operations portion of this manual.
5