Filter
Top Products
2
21
72
8
1
I
17
4
G
F
1
3
H
P Q
IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED
TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANT!
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS
NÉCESSAIRES POUR L'INSTALLATION.
1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top
of the LEFT PIVOT ARM (A).
Align the mounting holes of the LEFT HANDLEBAR with the mounting holes
at the top of the LEFT PIVOT ARM. Secure them together using three
SCREWS (1).
2. Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK
ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the
user side of the ROCKER ARM making sure that it seats fully over the
BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER
COVER over the opposite side of the ROCKER ARM in the same manner.
Secure the COVERS using two PHILLIPS PAN HEAD SCREWS (2). Tighten
the SCREWS securely. Do not over-tighten the SCREWS.
3. Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM
COVER (10). Position the BACK PIVOT ARM COVER over the user side of
the ROCKER ARM making sure that it interlocks with the ROCKER COVER.
Place the FRONT PIVOT ARM COVER over the opposite side of the PIVOT
ARM in the same manner. Secure the COVERS using two PHILLIPS PAN
HEAD SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
4. Remove the LEFT BULLHORN (B) from the BULLHORN MOUNTING
BRACKET (D) by removing the two SCREWS (C). The shipping installation is
upside-down from its final installed location. Rotate the LEFT BULLHORN so
the hand grip faces upwards and reinstall the LEFT BULLHORN using the two
previously removed SCREWS.
NOTE: IF THE ENTERTAINMENT OPTION WILL NOT BE USED,
CAREFULLY GATHER THE COAXIAL CABLE (P) AND POWER CORD
(Q) AND INSERT THEM INTO THE CONSOLE SUPPORT ASSEMBLY (7)
5. Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &
6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN
COVER (16).
NOTE: THE RIGHT PIVOT ARM COVERS ARE REVERSED FRONT AND
BACK. THE SCREWS WILL BE INSTALLED FROM THE REAR.
6. Unwrap the WIRE HARNESS (F,G,P,Q) leading from the MONOCOLUMN
(H). Feed the WIRE HARNESSES through the CONSOLE SUPPORT
ASSEMBLY TUBE (I) located at the top and front of the MONOCOLUMN.
Locate the CONSOLE SUPPORT ASSEMBLY (7) and position it near the top
of the MONOCOLUMN. Feed the WIRE HARNESSES through the
CONSOLE SUPPORT ASSEMBLY as shown. Align the bottom mounting
holes of the CONSOLE SUPPORT ASSEMBLY with those in the CONSOLE
SUPPORT ASSEMBLY TUBE. Secure them together using six SCREWS (1).
Tighten the SCREWS securely.
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRE HARNESSES (E & F)
WHEN ROUTING IT THROUGH THE CONSOLE SUPPORT ASSEMBLY
OR WHEN MOUNTING THE CONSOLE SUPPORT ASSEMBLY TO THE
CONSOLE SUPPORT ASSEMBLY TUBE.
7. Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the
top of the MONOCOLUMN (H) as shown. Be sure the ACCESSORY TRAY is
fully seated.
NOTE: BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS
WHEN SLIDING THE ACCESSORY TRAY INTO THE MONOCOLUMN.
Secure the accessory tray to the CONSOLE SUPPORT ASSEMBLY using
two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
9
11
1
10
2
A
5
6
2
B
C
15 22
A
D
E