Filter
Top Products
900 Series™ In-Dash Mounting Kit
3
531589-1_C
1-Year Limited Warranty
We warrant the original retail purchaser that products made by
Humminbird® have been manufactured free from defects in materials and
workmanship. This warranty is effective for one year from the date of original
retail purchase. Humminbird® products found to be defective and covered by
this warranty will be replaced or repaired free of charge at Humminbird®
option and returned to the customer freight prepaid. Humminbird® sole
responsibility under this warranty is limited to the repair or replacement of a
product that has been deemed defective by Humminbird®. Humminbird® is
not responsible for charges connected with the removal of such product or
reinstallation of replaced or repaired parts.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the product
installation and operation instructions;
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird®.
Please retain your original receipt as a proof of the purchase date. This will
be required for in-warranty service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD® AND WILL
BE THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED
IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN
NO EVENT WILL HUMMINBIRD® BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied warranty, or the exclusion
of incidental or consequential damages, so the above exclusions may not
apply to you. You may also have other rights, which vary from state to state.
Humminbird® Service Policy
Even though you'll probably never need to take advantage of our incredible
service policy, it's good to know that we back our products this confidently.
We do it because you deserve the best. We will make every effort to repair
your unit within three business days from the receipt of your unit at our
factory. This does not include shipping time to and from our factory. Units
received on Friday are typically shipped by the following Wednesday, units
received Monday are typically shipped by Thursday, etc.
All repair work is performed by factory-trained technicians to meet exacting
factory specifications. Factory-serviced units go through the same rigorous
testing and quality control inspections as new production units.
After the original warranty period, a standard flat rate service charge will be
assessed for each repair (physical damage and missing parts are not
included). Any repairs made after the original warranty will be warranted for
an additional 90 days after service has been performed by our factory
technicians. You can contact our Customer Resource Center or visit our web
site to verify the flat rate repair fee for your product (visit the Product Support
section):
http://www.humminbird.com
We reserve the right to deem any product unserviceable when replacement
parts are no longer available or impossible to obtain. This Service Policy is
valid in the United States only. This applies only to Humminbird® products
returned to our factory in Eufaula, Alabama. This Service Policy is subject to
change without notice.
DOMESTIC (USA) CUSTOMERS:
PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE
For all technical issues please call 1-800-633-1468
or visit www.humminbird.com, click SUPPORT.
Please reference product serial number and
model number when contacting Humminbird®.
© 2009 Humminbird®, Eufaula AL, USA.
All rights reserved.
900 Series™ In-Dash Mounting Kit
2
531589-1_C
4. Insert and tighten the two threaded rods into the two threaded inserts located on the back side of the control
head. Peel off the adhesive-backed foam pads and place them on the back of the control head; make sure you
notice the difference between the longer top/bottom and shorter side pads.
5. Insert the control head through the mounting hole from the front side of the dash. From the back side of the
dash, align the two threaded rods on the rear of the housing with the two holes on the in-dash mounting
bracket. Place a washer onto each threaded rod, then secure bracket by placing a wing nut onto each threaded
rod and tighten fully.
6. Insert cable connectors into the proper recesses on the cable collector insert. The cable connectors are keyed
to prevent reverse installation, so be careful not to force the connectors into the wrong slots. If you don’t have
a cable for every hole in the insert, install the blank plugs to protect the unit from the weather.
7. While holding cables in place in the cable collector insert, thread the cables through the slot in the bottom of
the cable collector cover, line up the cable collector insert and cover, then slide the cover into place on the insert.
NOTE: The tab on the cable collector insert goes into the slot on the cover.
8. Attach the cable collector insert to the cable collector cover using the 2 Phillips screws provided.
9. Plug the cable collector assembly into the back of the control head. Cable connectors and cable sockets are
keyed to prevent reverse installation, so be careful not to force the connectors into the wrong sockets. Once the
cable collector and all cables are plugged into the back of the control head, lock the assembly into place by
threading the knurled screw into the threaded insert on the back of the housing. (Cable ties are provided to help
you secure the cables in place by threading them through the available holes on the in-dash bracket).
NOTE: It is very important that the cable collector is used and secured in place in the In-Dash installation.
Plug Cable Connector Assembly to Back of Control Head
Knurled
Screw
Foam Pads
Threaded
Insert
Wing Nut
Threaded Rod
Expansion ports -
use for future
accessories
Washers
Cut Away
Dash
In-Dash
Bracket
© 2009 Humminbird®, Eufaula AL, USA.
All rights reserved.
Power
Temp/Speed
Communications
Transducer
Cable Collector
Insert
Screws
Tab on
Insert
Slot on
Cover
Cable
Collector
Cover
Cable Collector
Insert