Filter
Top Products
12/01 P/N 211488E
5
INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF
THIS OWNERS MANUAL
1. Remove all contents from underside of tank. Keep tank (1) bottom side
up. Install wheel axle (2) through wheel carriage (67) and install wheels
(3) onto wheel axle (2) with spacers (69) as shown. Secure wheel bracket
as shown, a deep socket is recommended.
IMPORTANT! DO NOT OVER TIGHTEN.
2. Correctly identify each pole section and mark indicated distance from ends
with tape as shown.
3. Align pole top and middle pole sections as shown using alignment mark
and hole.
IMPORTANT! Holes in top (4) and middle pole (5) sections MUST
align to correctly position elevator system toward playing surface.
Bounce pole top (4) and middle section (5) together as shown until they
no longer move toward taped reference mark. NOTE: Pole sections
should have a 3-1/2" (9 cm) minimum overlap.
4. IMPORTANT! Holes in top (4) and bottom pole (6) sections MUST
align to correctly position elevator system toward playing surface.
Add bottom pole section (6) to assembly as shown using alignment mark
and hole, and bounce until completely tight. Once assembled, pole
sections CAN NOT be separated! NOTE: Pole sections should have a
3-1/2" (9 cm) minimum overlap.
5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8).
6. Insert pole assembly into tank assembly as shown. Secure pole assembly
with upper pivot bracket (9) and lock nut (10).
7. Secure base struts (11) to pole using bolt (12), washers (13), and nut (14),
as shown. Place vinyl bolt cover (46) over exposed bolt threads. Rotate
the non-secured ends of base struts (11) as shown.
8. Secure base struts (11) to base using bolt (16), washers (13), and
nut (17).
9. Insert carriage bolts (18) into middle set of holes on wheel bracket (19) as
shown.
10. Attach lower pivot bracket (20) to wheel bracket (19) using bolt (21),
washers (13), disc (22), and nut (10) as shown.
11. Attach handle bar (23) to wheel bracket assembly using nuts (17) as
shown.
12. Install wheels (3) onto axle (24) and wheel bracket assembly with push
caps (25) as shown.
13. Attach wheel bracket assembly to base assembly using bolt (26), washers
(13), and nut (10) as shown.
14. NOTE: Two people recommended for this step. Carefully reposition
entire assembly to upright position.
Attach front of plastic handle (27) to back of plastic handle (28) around
handle bar (23) using self-tapping screws (58) as shown.
IMPORTANT! Front of plastic handle (27) should face outward, away
from pole assembly.
15. Insert bolts (30) through plastic handle assembly, handle bar (23) and
attach nuts (17) as shown. Tighten completely.
16. Install net clips (21).
The Quick Clip™ rapid release net system lets the net pull away from the
rim. This reduces the risk of player injury or property damage. However,
improper installation or a ball making contact at an odd angle may
disengage the net clip from the goal rim. Usually, the clip is reinstalled
with little or no problem. We hope that you agree this inconvenience is
minor when compared to the safety of the players. Quick Clip: US Patent
No. 5,792,010/5,795,253
The two outer hooks on net clip must face towards inside of goal rim.
Insert larger hole in net clip onto rim stud, push down on net clip, then
slide net clip right, locking or snapping securely into position (clips must
"snap" into place to insure a secure fit).
NOTE: Net clips should not slide with ease. It is very important that the
net clips are in the locked position before going on to next step.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER
INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT
PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW
DIRECTIONS CAREFULLY.
17. Attach elevator bracket (33) to middle pole section (5) using bolts (34),
reinforcement bracket (29), and nuts (17) as shown.
18. Attach backboard support brackets (35) to the backboard frame using
bolts (36), spacers (37), and nuts (38) as shown.
19. Attach lower elevator tubes (42) to backboard support brackets (35) using
spacers (39), bolt (41), and nut (40) as shown. NOTE: Rim mounting
nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers
here on spring return style rims.
20. Attach upper elevator tubes (45) to backboard support brackets (35) using
spacers (43), bolt (44), and nut (40) as shown.
21. A.Attach upper and lower elevator tubes (45, 42) to upper pole
section (4) using bolts (44, 41) and nuts (40) as shown. Attach pole
cap (48) as shown.
B.Attach counterbalance spring (48) to upper elevator tubes (45) with bolt
(49) and nut (14) in location shown. Stretch spring to lower elevator
tubes (42) and attach with hardware (50, 10) as shown.
NOTE: Slide counterbalance spring against elevator tubes.
22. Insert locking pin (52) into bracket on adjustment tube (51). Insert cross
pin (53) through hole in bracket and locking pin (52) as shown in
figure A. Fit left handle (54) onto adjustment tube (51) so the bottom of
adjustment tube (51) sits on the two small ribs of the handle as shown in
figure B.
23. Insert spring (56) into back of locking pin (52) as shown. Spring (56)
should rest between two small ribs at the back of the plastic handle as
shown in Figure C. Insert top of trigger (57) into bracket on the
adjustment tube (51) as shown. The plastic post of the handle pieces
should go through the hole in bottom of trigger (57) and hold it into place
as shown.
24. Finish handle assembly by attaching right handle (55) using screws (58)
as shown.
25. Attach adjustment tube (51) to lower elevator tubes (42) using bolt (41),
spacers (59), and nut (40) as shown.
26. Insert lower adjustment rod (60) into bottom of adjustment tube (51), pull
trigger to allow lower adjustment rod (60) to move about mid-way into
adjustment tube (51), release trigger so the lower adjustment rod (60)
locks into position midway inside adjustment tube (51). Attach lower
adjustment rod (60) to elevator bracket (33) using bolt (61) and nut (14) as
shown.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT
IN BODILY INJURY.
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN
EMPTY, MAY TIP OVER.
27. Roll the completed assembly to the desired playing area. Insert the
T-strap (15) through the slot on the back of the base as shown. Secure
the unit to ground by twisting the tie down stake (62) into the ground and
hooking the T-strap (15) onto the tie down stake (62). Fill tank with 33
gallons of water.
IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in
sub-freezing climates.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN
EMPTY, MAY TIP OVER.
28. Apply the height adjustment and moving label (64) to the front of the pole
as shown.
29. Install net (65).
IMPORTANT! Make sure net is held by all three hooks on the net
clip.
A.Slide net into outer hook as shown.
B.Slide net into second outer hook creating a loop as shown. Push loop
to back of clip.
C.Pull loop up and through back of clip, snapping over the middle hook.
D.Pull net down to make sure it is held securely by all three hooks.
NOTE: If net releases during normal play, net was improperly installed.
Please review instructions to install net properly.
30. Lock elevator system into highest position (so the backboard is as high as
it will go). Apply 10 ft. height indication sticker (66) to adjustment tube
(51) directly below arrow on handle as shown. Move elevator system to
the next position and apply the 91/2 ft. sticker. Repeat until all height
settings have been labeled. (8-10ft.)
31. Pull trigger (57). Move elevator system up or down to desired height,
release trigger (57) to lock system into one of the five height settings.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.