Filter
Top Products
10
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
11
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
A S S E M B LY S T E P 3
HARDWARE BAG 3 CONTENTS :
FLAT WASHER (J)
CONSOLE MAST
CONSOLE CABLES
SPRING WASHER (I)
BOLT (H)
CONSOLE
DO NOT ATTACH
THIS SIDE UNTIL STEP 3-D
ARC WASHER (K)
FLAT WASHER (J)
19 mm
Qty: 2
SPRING WASHER (I)
15 mm
Qty: 4
BOLT (H)
15 mm
Qty: 4
ARC WASHER (K)
17 mm
Qty: 2
A Open HARDWARE BAG 3.
B With running deck in lowered position, place CONSOLE on the console masts. Align the
brackets that are underneath the console with the top holes of the console masts.
C To assemble the CONSOLE to the LEFT CONSOLE MAST, insert 1 BOLT (H), 1 SPRING
WASHER (I) and 1 FLAT WASHER (J) into the side hole and insert 1 BOLT (H), 1 SPRING
WASHER (I) and 1 ARC WASHER (K) into the back hole in the LEFT CONSOLE MAST
and lightly tighten.
D Gently lift RIGHT side of the CONSOLE to connect the CONSOLE CABLES. Carefully tuck
wires in mast to avoid damage. NOTE: Do not pinch console cable or grip pulse wires.
E Repeat STEP C above to assemble the RIGHT CONSOLE MAST to the CONSOLE.
F Leave console bolts loose until after STEP 4 is completed.
A S S E M B LY S T E P 2 ( C O N T I N U E D )
FLAT WASHER (E)
BOLT (D)
RIGHT CONSOLE MAST
MAIN FRAME
WAVY WASHER (F)
ELEVATION FRAME
CONSOLE CABLE
PRE-ATTACHED BOLT
FOOT LOCK LATCH
RIGHT LINKAGE ARM
PRE-ATTACHED NUT
PRE-ATTACHED
TEFLON WASHER
1
3
2
NOTE: If you have attempted to
move the treadmill from the box
and the machine has sprung
open and cannot be assembled,
refer to the troubleshooting
section in order to restore the
treadmill to its proper position.
*
Insert 1 BOLT (D) and 1 FLAT WASHER (E) through
RIGHT CONSOLE MAST
followed by 1 WAVY WASHER (F)
and attach to MAIN FRAME.
Unscrew PRE-ATTACHED NUT and remove from RIGHT
LINKAGE ARM and discard. Carefully move RIGHT LINKAGE
ARM and PRE-ATTACHED TEFLON WASHER into position
and attach to ELEVATION FRAME.
NOTE
: While holding RIGHT CONSOLE MAST in the
upright position, tighten PRE-ATTACHED BOLT using
T-wrench to attach RIGHT LINKAGE ARM.
Cut band holding FOOT LOCK LATCH assembly. Lift the
RUNNING DECK
until lock latch on side of treadmill is
fully engaged.
Remove CONSOLE from box and place out of the way.
Lower the treadmill RUNNING DECK from the folded
position by stepping on LOCK LATCH on lower right side.
E
F
G
H
I
HARDWARE BAG 2 CONTENTS:
LOCK LATCH PIN (G)
Qty: 1
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
CT7.0_Rev.1.3.indd 10-11 6/20/08 9:56:58 AM