Filter
Top Products
TIDE” appears. Future date will be
displayed on the lower half, future
tide graph and hourly time will be
displayed on the upper half.
Press and hold LIGHT/SET button
for two seconds; year digits will flash.
To advance flashing year digits,
press START button. Press MODE
button; months digits will flash. To
advance months digits, press START
button. Press MODE button; date
digits will flash. To advance date
digits, press START button. When
future date setting is complete, press
LIGHT/SET button. Press START
button; cursor will scroll across tide
graph, indicating tide conditions for
any hour of the day on the future
date selected. Note: Hourly time is
indicated beneath “FT” on the upper
half of display.
HOW TO OPERATE
CHRONOGRAPH/STOPWATCH
Press MODE button until “CHRONO”
appears. “CHRONO RESET” will be
displayed on the upper half;
chronograph time on the lower half.
Reset the chronograph to zero by
pressing STOP/RESET button.
Press START button to start
chronograph.
Press START button to view split
time. Split time is the time elapsed
since the start of the chronograph.
Chronograph will continue to count
while split time is displayed. Each
press of START button will display
a split time.
To stop chronograph, press
STOP/RESET button. Reset the
chronograph to zero by pressing the
STOP/RESET button.
HOW TO SET AND OPERATE THE
ALARMS
Press MODE button until “ALARM”
appears. There are four different
alarms, which can be set as daily
HOW TO OPERATE THE
COUNTDOWN TIMER
Press MODE button until “TIMER”
appears. During the setting process
you can select from three different
countdown timer functions.
Countdown/stop (CS): timer counts
down from a preset time to zero and
stops. Countdown/repeat (CR):
timer counts down from a preset
time to zero, resets and repeats.
Countdown/count up (CU): timer
counts down from a preset time to
zero and begins to count up.
Press and hold LIGHT/SET button
to enter the countdown timer setting
mode.
The seconds digits will flash. Press
START button to advance
seconds digits.
Press MODE button; hours digits
will flash. Press START button to
advance the hour digits.
Press MODE button; minutes digits
will flash; press START button to
advance minutes digits.
Press MODE button; CR, CS or CU
will flash. Press START button to
select which countdown timer you
wish to use.
When countdown time setting is
complete, press LIGHT/SET button
to exit the setting mode. To start
timer, press START button. To stop
timer, press STOP/RESET button.
To reset timer, press LIGHT/SET
button.
HOW TO SET DUAL TIME
Press MODE button until “TIME-2”
appears. To set dual time, press
and hold LIGHT/SET button;
seconds digits will flash. Press
START button to reset the seconds
digits to zero. Continue through the
setting sequence as done in “TIME-
1”, setting by cycling between
MODE button and START button.
When dual time setting is complete,
press LIGHT/SET button to exit the
setting mode.
CARE AND MAINTENCE
1. Back case cover should only be
removed by an authorized watch
repair specialist.
2. Always rinse your watch in fresh
water after immersion in salt or
chlorinated water.
3. Do not expose watch or band to
chemicals such as gasoline, aerosol
sprays, paint or solvents.
4. Periodically clean with a soft cloth
and fresh water.
NOTE: Extreme electrostatic
discharge can cause the LCD to
‘freeze up’. In this event you could
reset the watch by pressing all 4
buttons together for 5 seconds.
TIDE LOCATIONS
WEST USA
SAN DIEGO,CA
LA JOLLA, CA
SAN CLEMENTE, CA
NEWPORT BAY, CA
CABRILLO BEACH, CA
LOS ANGELES HARBOR, CA
SANTA MONICA, CA
MALIBU, CA
VENTURA, CA
RINCON, CA
SANTA BARBARA, CA
GAVIOTA, CA
POINT ARGUELLO, CA
MORRO BEACH, CA
CARMEL COVE, CA
MONTEREY BAY, CA
MOSS LANDING, CA
SANTA CRUZ, CA
OCEAN BEACH, CA
repeating alarms, or one time only
reminder alarms. To set a one time
alarm, you must set a specific date.
To set a daily repeating alarm, date
position must be set to “-----”.
Additionally, the four different alarms
may be set to reference either
“TIME-1” or dual time “TIME-2.”
Pressing STOP/RESET button will
toggle between the four
different alarms.
Press and hold LIGHT/SET button
to enter alarm setting mode. The
hours digits will flash. Press START
button to advance the flashing hours
digits; hold for rapid advance. Press
MODE button; minutes digits will
flash. Press START button to
advance minutes digits. Press
MODE button; months digits will
flash; to set a one time only reminder
alarm, you must set a date. Press
START button to advance months
digits. To set this alarm as a daily
repeating alarm, enter (--) instead
of specific months digits.
Press MODE button; date digits will
flash. To set a one time only
reminder alarm, press START button
to advance date digits. To set this
alarm as a daily repeating alarm,
enter (--) instead of specific date
digits. Press MODE button; “T1” or
“T2” will flash. Press STOP/RESET
button to indicate if this alarm is in
reference to “TIME-1”, or dual time
“TIME-2”. Press LIGHT/SET button
when alarm 1 setting is complete.
Press STOP/RESET button to
advance to alarm 2, 3 or 4. To set
any of these alarms, follow setting
sequence for alarm 1 as detailed
above.
Once any of the alarm times are
set, the alarm is automatically
activated (armed), and is indicated
as “ ” on the display. To arm or
disarm any of the four alarms while
in alarm mode, press STOP/RESET
button to select alarm. Once
selected, press START button to
arm or disarm the alarm “ ” and/or
hourly chime “ ”. The setting
sequence is:
Hourly chime on: “ ”
Alarm on: “ ”
Both alarm and
hourly chime on: “ ”
Both alarm and
hourly chime off: no symbol