Filter
Top Products
Operation Guide 3271
E-20
• A graphic animation plays on the display while a stopwatch timing operation is being
performed. You can toggle the animation on and off by holding down A while the
stopwatch is reset to all zeros.
More than 10 hours
• Whenever the elapsed time exceeds 10 hours, the measurement changes from
1/100-second units to 1-second units.
E-21
Recall Mode
Use the Recall Mode to recall and delete records stored
by the Stopwatch Mode.
• Stopwatch records are stored in “logs” that are created
automatically by the watch. See “Memory Management”
on page E-47 for more information.
• The title screen of the newest log appears first whenever
you enter the Recall Mode.
• Log numbers are automatically assigned in sequence,
starting from 01.
• All of the operations in this section are performed in the
Recall Mode, which you enter by pressing C (page E-9).
To recall stopwatch records
In the Recall Mode, use A to scroll through the log title
screens, starting from the newest one, as shown below.
When the title screen of the log you want is displayed, use
D (+) and B (–) to cycle through the records contained in
the log.
Log number
Creation date
(Month – Day)
Log Title Screen
Time measurement
was performed
E-22
D
Split time
Lap/Split number
BEST indicator
A
Log Title Screen
Stopwatch Record
Screen
Best Lap Time
Screen
Lap time
▲
▲
▲
▲
A
▲
▲
B
▲
D
B
D
B
▲
E-23
• The locations of the lap time and split time in the Stopwatch Record screen are
determined by the display format you last selected in the Stopwatch Mode (page
E-17).
• The BEST indicator identifies the record that contains the best lap time in the log.
• If a best lap time record is deleted automatically when the log becomes full, the
BEST indicator will not be transferred to the record with the next best lap time. See
“Memory Management” on page E-47 for more information about automatic deletion
of records.
To delete a log
1. In the Recall Mode, display the title screen or one of the records of the log you want
to delete.
2. While holding down B, hold down D for about two seconds until the watch beeps.
• “CLR” will flash on the display for two seconds and then the watch will beep.
Release B and D at this time.
• You cannot delete the log of an ongoing elapsed time measurement operation.
E-24
To delete all logs
1. While holding down B, hold down D for about five seconds until the watch beeps
once and then a second time.
• “CLR” will flash on the display for two seconds and then the watch will beep once.
Keep B and D depressed and “ALL” will flash on the display for three seconds,
and then the watch will beep again. This indicates that all log data is cleared.
• You cannot delete logs while an elapsed timing operation is in progress.
E-25
Countdown Timer
Dual timers can be set with two different starting times.
The watch can be configured so the two timers alternate,
so when one reaches the end of its countdown, the other
timer starts. You can specify a “number of repeats” value,
which controls how many times the two-timer countdown
operation is performed (1 = once, 2 = twice, etc.). The
starting time of each timer can be set in five-second steps
up to 99 minutes, 55 seconds.
You can specify up to 10 repeats. The watch emits a short
beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch
emits a 5-second beep when the end of the final timer
operation (specified by the number of repeats) is reached.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
Seconds
Minutes Timer 1
Number of Repeats
E-26
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-28) to display it.
2.Press C to move the flashing in the sequence shown
below to select other settings.
Timer 1
Minutes
Timer 1
Seconds
Timer 2
Seconds
Timer 2
Minutes
Number of Repeats
E-27
• To disable either timer, set 00'00" as its countdown start time.
4. Press A to exit the setting screen.
Button Operation
Use D (+) and B (–) to change the setting.
Use D (+) and B (–) to change the setting.
Setting
Minutes, Seconds
Number of Repeats
Screen
3. When the setting you want to change is flashing, use D and B to change it as
described below.
E-28
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
• Press D to pause a countdown. Press D again to resume.
• Pressing B while a countdown timer is stopped resets it to the start time specified
by you.
• The watch emits a 5-second beep when the end of the final timer operation
(specified by the number of repeats) is reached.
• Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
Current timer time
Preset number of repeatsCurrent repeat count
Current time
Timer 1 or 2
(Reset)
(Start/Stop)
E-29
World Time
World Time shows the current time in 48 cities (31 time
zones) around the world.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “City Code Table” at the back of this
manual for information about the UTC differential
settings that are supported.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C
(page E-9).
Current time in
selected city
City code