Filter
Top Products
Operation Guide 3257
E-20
• The locations of the lap time and split time (middle or bottom of the display) in the
Stopwatch Record screen are determined by the display format you last selected in
the Stopwatch Mode (page E-11).
• The BEST indicator identifies the record that contains the best lap time in the log.
• If a best lap time record is deleted automatically when the log becomes full, the
BEST indicator will not be transferred to the record with the next best lap time. See
“Memory Management” on page E-37 for more information about automatic deletion
of records.
• The unit of measurement used for the distance calculation depends on the unit you
select for your stride length as shown in the table below. See “To configure your
basic data” on page E-15 for more information.
Selected Stride Unit Distance Unit
XM (centimeters) km (kilometers)
Yn (inches) mi (miles)
E-21
To delete a log
1. In the Recall Mode, display the title screen of the log you want to delete.
• See “To reset the cumulative total screen” below for information about what
happens when you select the cumulative total screen here.
2. Hold down C and D until the watch beeps and
CLR stops flashing on the
display.
• This deletes the log and all the records inside it. Deleting a log does not change the
cumulative total distance value.
To reset the cumulative total screen
1. In the Recall Mode, display the cumulative total screen.
2. Hold down C and D until the watch beeps and
CLR stops flashing on the
display.
• This resets the cumulative total distance to zero, without deleting any logs or
records. A new cumulative total will start with the next stopwatch operation you
perform.
E-22
Countdown Timer
You can set the countdown timer within a range of one
minute to 100 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• Countdown timer functions are available in the
Countdown Timer Mode, which you can enter using B
(page E-5).
To set the countdown start time
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
Hours
Minutes
Seconds
Timekeeping Mode time
E-23
• If the countdown start time is not displayed, use the procedure under “To use the
countdown timer” to display it.
2. Press B to move the flashing between the hour and minute settings.
3. Use D (+) and C (–) to change the flashing item.
• To set the starting value of the countdown time to 100 hours, set 0:00.
4. Press A to exit the setting screen.
To use the countdown timer
Press C while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value when the alarm sounds.
• Press C while a countdown operation is in progress to pause it. Press C again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing C), and then
press D. This returns the countdown time to its starting value.
E-24
To turn auto-repeat on and off
While the countdown start time is displayed on the
Countdown Timer Mode screen, hold down D for about
two seconds to toggle auto-repeat on (
displayed) and
off ( not displayed).
• When auto-repeat is turned on, the alarm sounds and
countdown starts again whenever the countdown
reaches zero. You can stop the countdown by pressing
C, and manually reset to the countdown start time by
pressingD.
• Auto-repeat timing repeats up to seven times.
Auto repeat on indicator
E-25
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered 1 through 5.
The hourly time signal screen is indicated by :00.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B (page E-5).
Alarm number
Alarm time
(Hour : Minutes)
Timekeeping Mode time
E-26
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
x3
x4
x1 x2
:00 x5
• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
through 5 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
3. Press B to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and C (–) to change it.
E-27
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, until
you turn the alarm off or change it to a one-time alarm (page E-28).
Note
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-6)
Displaying the Alarm
1
setting screen (page E-26)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-28
To select the operation of Alarm
11
11
1
1. In the Alarm Mode, use D to select Alarm1.
2. Press C to cycle through the available settings in the sequence shown below.
SNZ indicator and one-time alarm on indicator
One-time alarm on Snooze alarm on Alarm off
• The applicable alarm on indicator is displayed in all modes when an alarm is turned
on.
• The SNZ indicator flashes during the 5-minute intervals between alarms.
• Displaying the Alarm 1 setting screen (page E-26) while the snooze alarm is turned
on automatically turns off the snooze alarm (making Alarm1 a one-time alarm).
E-29
To turn Alarms
22
22
2
through
55
55
5
on and off
1.In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 through 5).
2.Press C to toggle the displayed alarm on and off.
• Turning on a one-time alarm (2 through 5) displays the
one-time alarm on indicator (
) on its screen.
• The one-time alarm on indicator is displayed in all
modes.
• If any alarm is on, the alarm on indicator is shown on
the display in all modes.
One-time alarm
on indicator