Filter
Top Products
Operation Guide 5160
E-28
EL backlight: Automatic, manual
Battery: One lithium battery (Type: CR2016)
Battery life:3 years under the following conditions
• 2-second backlight operation per day
• 20-second alarm operation per day
E-27
Specifications
Accuracy at normal temperature: ±30 seconds a month
3-hand: Hour, minute, second
Timekeeping Mode: Hour, minutes, seconds, am/pm(P), month, day, day of the week
Time system: Switchable between 12-hour and 24-hour formats
Calendar system: Full auto-calendar pre-programmed from 2000 to 2099
Standard time/Daylight saving time
Stopwatch Mode
Measuring unit:1/100 of a second (up to 59' 59" 99)
1 second (from 1:00' 00")
Measuring capacity: 9 hours, 59 minutes, 59 seconds
Functions: Elapsed time, lap time and split time
Memory: 10 records (laps, splits)
Alarm Mode: Daily alarm, hourly time signal
E-26
To turn a daily Alarm and the Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Hourly Time
Signal Only
Daily Alarm
Only
Both OFF Both ON
To test the alarm
Hold down B in any mode (except when making any settings) to sound the alarm.
Note that this operation also changes the mode.
E-25
3. Press C to increase the selected digits. Holding down C changes them at high
speed.
4. After you make the settings you want, press A to exit the input screen.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
E-24
Alarm Mode
When a Daily Alarm is turned on, the alarm sounds for
about 20 seconds at the preset time each day. Press any
button to stop the alarm after it starts to sound. When the
Hourly Time Signal is turned on, the watch beeps every
hour on the hour.
To set the alarm time
1.Hold down A while in the Alarm Mode, until the hour
digits starts to flash on the display, indicating the setting
screen. The alarm is automatically turned on at this
time.
2.Press B to change the selection in the sequence
shown below.
Hour Minutes
Hour
Minutes
Mode indicator
Current time
Hourly Time Signa
l
indicato
r
Daily Alarm indicator
E-23
Minutes
Seconds
1/100 second
Lap number
LAP indicator
Minutes
Seconds
1/100 second
Split number
SPL indicator
[LAP time display] [SPLIT time display]
E-22
Recall Mode
Use the Recall Mode to recall the lap times and split times stored in memory.
• Press A to toggle the display between lap times and split times.
• Press C to scroll through Recall Mode records.
Starting a new elapsed time operation in the Stopwatch Mode automatically clears the
data (lap or split) that is currently displayed in the Recall Mode.
E-21
3.Press C as each runner finishes. The finish time and
sequence number remains on the display for about
seven seconds. Stopwatch timing continues internally.
• The first nine split times (finish time) you record are
stored in memory. The final time you record when you
press A is also stored, for a total of 10 times.
•
If you continue to perform the split time operation after
there are already nine times in memory, the split times
are shown on the display but are not stored into memory.
• You can perform up to 99 split time operations (9 stored
+ 90 unstored) during each elapsed time operation.
• You can recall split times using the Recall Mode.
4.Press A to stop the time measurement.
5.Press C to clear the stopwatch to all zeros.
Minutes
Seconds
1/100 second
Sequence number
E-20
• The first nine split times you record are stored in
memory. The final time you record when you press A is
also stored, for a total of 10 times.
•
If you continue to perform the split time operation after
there are already nine times in memory, the split times
are shown on the display but are not stored into memory.
• You can perform up to 99 split time operations (9 stored
+ 90 unstored) during each elapsed time operation.
• You can recall split times using the Recall Mode.
4.Press A to stop the time measurement.
5.Press C to clear the stopwatch to all zeros.
To record multiple finishes
1.In the Recall Mode, use A to select split time as the
timing operation.
• See “Recall Mode” for more information about selecting
the stopwatch operation.
2.Enter the Stopwatch Mode, and then press A to start
the stopwatch.
Minutes
Seconds
1/100 second
Split number
SPL indicator