Casio MA0904-EA Watch User Manual


  Open as PDF
of 5
 
Operation Guide 3163
3
To use the countdown timer
1. In the Countdown Timer Mode, press
B
to scroll through the start times and
display a preset start time or the Custom Timer screen.
Each press of
B
scrolls through the start time screens as shown below.
0RESS
0RESET3TART4IME #USTOM4IMER
MINUTE
HOUR
#USTOM4IMER
   
2. Press
D
to start the countdown of the timer you selected in step 1.
•
The countdown timer operation continues even if you
exit the Countdown Timer Mode.
•
Press
D
while a countdown operation is in progress to
pause it. Press
D
again to resume the countdown.
•
To stop a countdown operation completely, fi rst pause
it (by pressing
D
), and then press
B
. This returns the
countdown time to its starting value.
•
With the Countdown/Count Up Timer, an alert sounds
and the watch starts an elapsed time measurement
operation when the end of the countdown is reached.
Pressing
D
will stop the elapsed time measurement
operation. Pressing
B
while elapsed timing is stopped
will reset the timer to its start time.
Stopwatch
$AY
SECOND
(OURS-INUTES3ECONDS
The stopwatch lets you measure elapsed time, split times,
and two fi nishes.
•
The display range of the stopwatch is 99 days, 23 hours,
59 minutes, 59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
.
To measure times with the stopwatch
%LAPSED4IME
3PLIT4IME
4WO&INISHES
3TOP
2ESTART 3TOP
#LEAR
3TART
3TART
3PLIT
30,DISPLAYED
3PLITRELEASE 3TOP #LEAR
3TART
3PLIT 3TOP 3PLITRELEASE #LEAR
&IRSTRUNNER
FINISHES
$ISPLAYTIMEOF
FIRSTRUNNER
3ECONDRUNNER
FINISHES
$ISPLAYTIMEOF
SECONDRUNNER
Alarms
!LARMTIME
(OUR-INUTES
Your watch has fi ve independent multi-function alarms.
You can set the hour and minute for the alarm time, and
you can select one of four repeat patterns (week day,
weekend, daily, one-time). One of the alarms is a snooze
alarm.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour. You can
specify the Hourly Time Signal repeat pattern, and a start
time and end time.
•
There are fi ve alarm screens, each of which shows an
alarm name: ALARM1 to ALARM4, and SNOOZE. The
Hourly Time Signal is indicated by SIGNAL.
•
When you enter the Alarm Mode, the data you were
viewing when you last exited the mode appears fi rst.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
.
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm
screens until the one whose settings you want to
confi gure is displayed.
•
Select alarm screen ALARM1 through ALARM4 to
confi gure a normal alarm. Select the SNOOZE alarm
screen to confi gure the snooze alarm.
•
The snooze alarm repeats every fi ve minutes.
2. After you select an alarm, hold down
A
until the hour
setting of the alarm time starts to fl ash, which indicates
the setting screen.
•
This operation turns on the alarm automatically.
3. Press
C
to move the fl ashing in the sequence shown below to select other
settings.
(OUR -INUTES 2EPEAT0ATTERN
4. While a setting is fl ashing, use
D
(+) and
B
(–) to change it.
•
You can select any one of the four alarm repeat patterns described below.
To confi gure the alarm to sound: Select this setting:
Daily DAILY
Once on the specifi ed date only ONCE
Daily on Saturday and Sunday WEEKEND
Daily from Monday through Friday WEEKDAY
5. Press
A
to exit the setting screen.
•
With the 12-hour format, set the time correctly as a.m. or p.m.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every fi ve minutes, until you turn the alarm off.
•
Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
•
To stop the alarm tone after it starts to sound, press any button.
•
When Flash Alert is turned on, the red and green LEDs at the bottom of the display
will fl ash in time with the alarm beeper.
•
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm Mode setting screen
To test the alarm
In the Alarm Mode, hold down
D
to sound the alarm.
To turn an alarm on and off
3NOOZEALARMINDICATOR
!LARMONINDICATOR
/N/FFSTATUS
1. In the Alarm Mode, use
D
to select an alarm.
2. Press
B
to toggle it on (on) and off (– – displayed).
•
Turning on an alarm (ALARM1 to ALARM4, or
SNOOZE) displays the alarm on indicator on its Alarm
Mode screen.
•
In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
•
The alarm on indicator fl ashes while the alarm is
sounding.
•
The snooze alarm indicator fl ashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
To confi gure Hourly Time Signal settings
%NDTIME3TARTTIME
1. In the Alarm Mode, use
D
to display the Hourly Time
Signal (SIGNAL) screen.
•
Hourly Time Signal times are displayed using the
24-hour time format.
2. Hold down
A
until the Hourly Time Signal start time
starts to fl ash. This is the setting screen.
•
This also will turn on the Hourly Time Signal.
3. Press
C
to move the fl ashing in the sequence shown
below to select other settings.
3TART4IME %ND4IME 2EPEAT0ATTERN
4. While a setting is fl ashing, use
D
(+) and
B
(–) to change it.
•
When the start time and end time settings specify a period that is 24 hours long
(such as a start time of 7:00 a.m. and an end time of 6:00 a.m.),
is displayed.
•
If you set the same time for both the start time and end time (a single hourly time
signal), only the start time will be displayed on the Hourly Time Signal screen.
(Example: 8:00)
•
You can select any one of the three Hourly Time Signal repeat patterns described
below.
To confi gure the Hourly Time Signal to sound: Select this setting:
Daily DAILY
Daily on Saturday and Sunday WEEKEND
Daily from Monday through Friday WEEKDAY
5. Press
A
to exit the setting screen.
•
With the 12-hour format, set the time correctly as a.m. or p.m.(P).
To turn the Hourly Time Signal on or off
(OURLYTIMESIGNAL
ONINDICATOR
1. In the Alarm Mode, use
D
to display the Hourly Time
Signal (SIGNAL) screen.
2. Press
B
to toggle the Hourly Time Signal on
(
(Check mark displayed.)) and off (
(Check mark not displayed.)).
•
An Hourly Time Signal on indicator is on the Alarm Mode
Hourly Time Signal screen while the Hourly Time Signal
is on.
•
The Hourly Time Signal on indicator is on the display in
all modes while the Hourly Time Signal is turned on.
 previous next