Filter
Top Products
2
Operation Guide 3118
To set an alarm time
1.In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
Press .
Press .
• To set an alarm, display one of the screens indicated by an alarm number from
through .
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
• To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
• The alarm will sound using the currently selected beeper pattern.
To turn an alarm on and off
1.In the Alarm Mode, use D and B to select an alarm.
2.Press A to toggle it on (
displayed) and off
(
displayed).
• Turning on an alarm (
through ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes besides the Alarm Mode, the alarm on
indicator is shown for any alarm that is currently turned
on.
• The alarm on indicator flashes while the alarm is
sounding.
Alarm on indicator
On/Off status
1/100 second
Minutes Seconds
Hourly time signal
on indicator
On/Off status
To turn the Hourly Time Signal on and off
1.In the Alarm Mode, use D and B to select the Hourly
Time Signal (
).
2.Press A to toggle it on (
displayed) and off
(
displayed).
• Turning on the Hourly Time Signal displays the Hourly
Time Signal indicator on its Alarm Mode screen.
• While the Hourly Time Signal is turned on, the Hourly
Time Signal on indicator is shown on the display in all
modes besides the Alarm Mode.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Start Stop Re-start Stop Clear
Two Finishes
Start Clear
Split Time
Start Split release Stop Clear
Split Stop Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Split
( displayed)
Timer number
Hours Seconds
Minutes
Countdown Timer
The Countdown Timer Mode has three 24-hour timers
whose starting time can be set in one-minute increments.
An alarm sounds when the countdown reaches zero.
• You also can select auto-repeat, which restarts the
countdown automatically from the original value you set
whenever zero is reached.
• All of the operations is this section are performed in the
Countdown Timer Mode, which you can enter using C.
To use a countdown timer
1. Press B while in the Countdown Timer Mode to select the timer whose time you
want to use.
• Pressing B does not change the timer selection if a countdown timer operation is
currently in progress or is paused. You must stop the ongoing countdown
operation before you can change to another timer.
2. Press D to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is reset automatically to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds to signal when the countdown
reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press B. This returns the countdown time to its starting value.
To set up a countdown timer
1.Press B while in the Countdown Timer Mode to select
the timer whose time you want to change.
• Pressing B does not change the timer selection if a
countdown timer operation is currently in progress or
is paused. You must stop the ongoing countdown
operation before you can change to another timer.
2.While the countdown start time is on the display, hold
down A until the hour setting of the countdown start
time starts to flash, which indicates the setting screen.
3. Press C to move the flashing in the sequence shown below to select other
settings.
Auto-repeatMinutesHours
4. While a setting is flashing, use D and B to change it as described below.
Screen Do this:
Use D (+) and B (–).
Press D.
To do this:
Change the hours or minutes
Toggle auto-repeat on ( ) and off ( )
• To specify a countdown start time of 24 hours, set .
5. Press A to exit the setting screen.
• The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
Edit Mode
You can use the Edit Mode to configure various settings, such as the alarm beeper
pattern.
The following are the settings that you can configure in the Edit Mode.
• Button operation tone on/off
• Alarm beeper pattern
• 12/24-hour timekeeping
• 00-second animation on/off
• All of the operations in this section are performed in the Edit Mode, which you enter
by pressing C.
• Each press of D or B cycles through available settings in the sequence shown
below.
Press .
Press .
Button Operation Tone
( )
Alarm Beeper Pattern
( )
12/24-hour Timekeeping
(
)
00-second Animation
( )
Button Operation Tone
The button operation tone sounds any time you press one of the watch’s buttons. You
can turn the button operation tone on or off as desired.
• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and
Countdown Timer Mode alarm all operate normally.
To turn the button operation tone on and off
1.In the Edit Mode, use D and B to display the Button
Operation Tone selection screen.
2.Press A to toggle the button operation tone on (
)
and off (
).
On/Off status