Filter
Top Products
USER’S GUIDE 2785
3
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes,
59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
Minutes
Seconds
1/100 second
To measure times with the stopwatch
Elapsed Time
Start
Stop Re-start Stop Clear
Start
Split
( displayed)
Split release Stop Clear
Start
Split Stop Split release Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
• The time on the screen may not appear to stop immediately when you press a
button to stop timing or to perform a split operation. Despite this, the time recorded
by your button operation is accurate.
Hand Setting
When the analog setting does not match the time shown
on the digital display, use this mode to correct the analog
setting.
• This watch features separate digital and analog
timekeeping. Note that the digital time and analog time
are independent of each other, and must be set
separately.
To set the analog time
1.Hold down A while in the Hand Setting Mode until
L/set starts to flash.
2.Use B and D to set the analog time.
• Each press of D advances the hands 20 seconds.
• Pressing B while holding down D causes the hand
setting to change at high speed, even if you release
the buttons. Press any button to stop.
• The analog time setting does not stop automatically when it reaches the current
time. You must stop the hands manually.
• Note that the hands can be advanced only and cannot be moved back. Take care
so you do not go past the setting you want to make.
3. After you set the analog time, press A to exit the setting screen.
• Depending on your timing when you operate the D button, the above operation can
cause the minute hand timing to become late. If this happens, repeat the above
operation to correct the minute hand timing.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display continually changes the contents of the
digital display.
To turn off Auto Display
Press any button (except for B) to turn off Auto Display.
To turn on Auto Display
In the Timekeeping Mode, hold down C for about three
seconds until the watch beeps.
• Note that Auto Display cannot be performed while a
setting screen is on the display.
Time Graph
The time graph appears in the Timekeeping Mode and
World Time Mode to provide a graphic indication of the
current hour, as described below. Note that only the hour
is indicated by
, which moves across the time graph
from left to right.
Timekeeping Mode: The time graph shows the current
hour in the city selected in the World Time Mode.
World Time Mode: The time graph shows the current
hour as kept in the Timekeeping Mode.
• The sun mark is displayed between 6:00 AM and 5:59
PM.
• The moon mark is displayed between 6:00 PM and 5:59
AM.
Minute hand
Hour hand
Sun mark
Moon mark
Inputting Text
The following describes how to input text in the e-DATA
MEMORY Mode.
To input characters
1.When the cursor is on the display, use D and B to
cycle through the available letters, numbers and
symbols, in the sequence shown below.
Cursor
(space)
to
(symbol)
to
(number)
Press . Press .
to
(lower-case)
to
(upper-case)
2. When the character you want is at the cursor position, press C to move the cursor
to the right.
3. Repeat steps 1 and 2 to input the rest of the characters you want.
• See the “Character List” for information about the characters you can input.
Auto Return Features
• If you leave the watch in the e-DATA MEMORY, City Temperature, or Alarm Mode for
two or three minutes without performing any operation, it automatically changes to
the Timekeeping Mode.
• If you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically saves any
settings you have made up to that point and exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the e-DATA MEMORY, World Time, or City Temperature Mode, the
data you were viewing when you last exited the mode appears first.
Timekeeping
• Resetting the seconds to
00
while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to
00
without changing the minutes.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
World Time
• The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
• The world time that appears in the lower part of the Timekeeping Mode screen
always uses 24-hour format, regardless of the watch’s current 12/24-hour setting.
• The current time in all World Time Mode cities is calculated in accordance with the
Greenwich Mean Time (GMT) differential for each city, based on the current Home
City time setting in the Timekeeping Mode.
• The GMT differential is the time difference of the time zone where the city is located
from Greenwich Mean Time.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Backlight Precautions
The backlight uses an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark.
In any mode, press B to illuminate the display for about two seconds.
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens the battery life.
Character List