Filter
Top Products
Operation Guide 3155
4
Recall Mode
You can use the Recall Mode to view the following data in watch memory.
• Times measured in the Rally Mode
• Total of the measured times currently in memory (TTL)
• You can use the D (forward) and B (back) buttons to scroll through records as
shown below. Holding down either button scrolls the records at high speed.
• Holding down the A button while a record is displayed will show the date and time
that the measurement was taken.
• To go straight to the total measured time screen, press the D and B buttons at the
same time.
• How the hour digits are displayed changes (to a format that requires two screens)
when the total measured time is within the range of 100 hours, 00 minutes and 00
seconds, to 2999 hours, 59 minutes 57 seconds. While the total measured time is
displayed in this case, the display will switch automatically between the two screens
at two-second intervals.
B
D
BB
AA
DD
Record 30 Record 1
Total measured
time
Record Number
Measured
elapsed time
Measurement date and time
Measured elapsed time
Measurement date
(Month – Day)
Measurement time
(Hour : Minutes)
Total measured
time
Hour digits screen
Total measured time (TTL)
When the total measured time is in
the range of zero to 2999 hours,
59 minutes 57 seconds
Minute digits screen
Switches automatically at
two-second intervals
Switches automatically at
two-second intervals
To correct recorded times
You can use the procedure below to correct times recorded by the watch so they
match official race times. The total measured time value also is updated in accordance
with the corrected times.
1.Hold down A until the display contents start to flash.
This is the setting screen.
2.Use the D (+) and B (–) buttons to change the
measured 1/10-second digit.
3.Press the C button to move the flashing to the
measured seconds.
4.Use the D (+) and B (–) buttons to change the
measured seconds.
5.Press the C button to move the flashing to the
measured minutes.
6.Use the D (+) and B (–) buttons to change the
measured minutes.
7.Press the C button to move the flashing to the
measured hours.
l
l
l
l
l
l
l
l
l
l
l
l
l
8. Use the D (+) and B (–) buttons to change the measured hours.
9. After the time is what you want, press the A button to exit the setting screen.
• You can change a measured time to a value up to 99 hours, 59 minutes, 59.9
seconds.
• Holding down the D (+) or B (–) button will scroll the selected value at high speed.
• To reset the data to all zeros, press the D and B buttons at the same time.
Measured
1/10 second
Measured
minutes
Measured
hours
Measured
seconds
CC
C
C
To delete all memory records
You can use the following procedure to clear all of the
measurement data records currently stored in watch
memory.
1.Use the D and B button to display the total
measurement time screen.
2.Hold down A until the display contents start to flash.
This is the setting screen.
3.Press the D (+) and B (–) buttons at the same time to
delete the records.
4.Press the A button to exit the setting screen.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
▲
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “UTC Differential/City Code List” for
information about the UTC differential settings that are
supported.
City code
Current time in
selected city
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C.
To view the time in another city
While in the World Time Mode, use the D (eastward) and B (westward) buttons to
scroll through the city codes (time zones). Holding down either button scrolls at high
speed.
• Pressing the D and B buttons at the same time will jump to the UTC time zone.
To toggle a city code time between Standard Time and Daylight Saving Time
1.In the World Time Mode, use D and B to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2.Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
• Note that changing the Daylight Saving Time for any city
code causes the setting to be applied to all city codes,
except UTC.
DST indicator
Alarms
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered
AL1, AL2,
AL3 and AL4 for the one-time alarm, a snooze alarm
screen indicated by
SNZ. The Hourly Time Signal
screen is indicated by
SIG.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm number
Alarm time
(Hour : Minutes)
Alarm date
(Month – Day)
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
• To set a one-time alarm, display an alarm screen AL1, AL2, AL3 and AL4.
To set the snooze alarm, display the
SNZ screen.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing in the sequence shown below to select other
settings.
Hour Minutes Month Day
4. While a setting is flashing, use D and B to change it as described below.
5. Press A to exit the setting screen.
Screen
To do this:
Change the hour
and minutes
Change the month
and day
Do this:
Use D (+) and B (–).
• With the 12-hour format, set the time correctly
as a.m. or p.m. (P indicator).
• To set an alarm that does not include a month
and/or day, set
for each setting.