Filter
Top Products
Operation Guide 5208
E-10
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C (page E-8).
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• When setting the time, you can also configure settings for the 12/24-hour format.
• Each press of D cycles the digital display in the sequence shown below.
D
Day
Day of week
D
D
▲
▲
PM indicator
Hour : Minute
SecondSecond Second
Month
▲
E-11
City code
Setting the Digital Time and Date
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the current digital time and date
1.In the Timekeeping Mode, hold down A for about two
seconds, until “ADJ” appears on the display.
• Your current Home City code will be flashing on the
screen.
2.Press C to move the flashing in the sequence shown
below to select other settings.
E-12
3. While the setting you want to change is flashing, use D and B to change it as
explained below.
Screen: To do this:
Change the city code
Toggle between Daylight Saving Time
(ON) and Standard Time (OFF).
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00
Do this:
Press D (east) and B (west).
PressD.
PressD.
PressD.
City Code
Language
Illumination
Duration
Day Month Ye a r
DST
12/24-Hour
Format
Seconds Hour Minutes
Button Operation
To ne
E-13
To do this:
Change the hour or minutes
Change the year
Change the month or day
Toggle the button operation tone
between (on) and (off)
Toggle the illumination duration between
LT1 (approximately 1.5 seconds) and
LT3 (approximately 3 seconds).
Change the day of the week language
ENG: English POR: Portuguese
ESP: Spanish FRA: French
DEU: German ITA : Italian
Screen:
Do this:
Use D (+) and B (–).
PressD.
PressD.
Use D (+) and B (–).
• See “City Code Table” at the back of this manual for a complete list of available
city codes.
E-14
4. Press A to exit the setting screen.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
12-hour and 24-hour timekeeping
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears for times in the
range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
E-15
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two seconds, until “ADJ” appears
on the display.
• Your current Home City code will be flashing on the screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON displayed) and Standard
Time (OFF displayed).
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears on the display to indicate that Daylight Saving Time is
turned on.
E-16
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting
When you change the Home City code and/or DST setting
• If the analog time does not match the digital time for any reason, use the procedure
described under “To adjust home positions” (page E-42) to match the analog setting
to the digital setting.
• Whenever you need to adjust both the digital and the analog time settings, make
sure you adjust the digital setting first.
• Depending on how much the hands have to move in order to synchronize to the
digital time, it may take some time before they stop moving.
E-17
World Time
The World Time Mode digitally displays the current time in
48 cities (31 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes (page E-11).
• After you press C to enter the World Time Mode, your
currently selected World Time City code will appear on
the digital display for about two seconds. After that, the
current time in that city will appear.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C
(page E-9).
City code
Current time in
selected city
E-18
To view the time in another city
If you press D while in the World Time Mode, your currently selected World Time City
code will appear on the digital display for about two seconds. After that, the current
time in that city will appear. Pressing D again while the World Time City code is
displayed will scroll to the next city code.
• For full information on city codes, see the “City Code Table” at the back of this
manual.
To toggle a city code time between Standard Time and Daylight Saving Time
1.In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2.Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
• The DST indicator will appear on the display whenever
you display a city code for which Daylight Saving Time is
turned on.
DST indicator
E-19
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Hold down A and B until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.