Filter
Top Products
Operation Guide 5235/5414 (OC)
E-15
To perform manual receive
1. Keep B depressed for at least two seconds as the
2
Second Hand goes through the following
sequence.
x Moves to YES (or Y for some models) or NO (N) to indicate the last signal reception result, then to
READY (R).
2. The
2
Second Hand indicates the operations the watch is currently performing.
When the 2
2
Second Hand is
pointed here:
It means this:
READY (R) Watch is setting up for reception.
WORK (W) Reception is in progress.
YES (Y) Reception was completed successfully.
NO (N) Reception failed for some reason.
x If signal reception is unstable, the 2
2
Second Hand may move between WORK
(W) and READY (R).
x When the receive operation is successful, the watch adjusts the time setting
accordingly, and then resumes regular timekeeping. It does not adjust the
setting if the operation failed.
Note
x To interrupt a receive operation and return to regular timekeeping, press any
button.
Module 5235
Module 5414
30
2
30
2
E-14
x Signal reception may be diffi cult or even impossible under the conditions described below.
Inside or among
buildings
Inside a vehicle Near household
appliances,
offi ce
equipment, or a
mobile phone
Near a
construction
site, airport, or
other sources of
electrical noise
Near high-
tension power
lines
Among
or behind
mountains
2. What you should do next depends on whether you are using Auto Receive or Manual Receive.
x Auto Receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”
for details.
x Manual Receive: Perform the operation under “To perform manual receive”.
Auto Receive
x With Auto Receive, the watch performs the receive operation each day automatically up to six times
(up to fi ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. When any
receive operation is successful, none of the other receive operations for that day are performed.
x When a calibration time is reached, the watch will perform the receive operation. The receive operation
is not performed if a calibration time is reached while you are confi guring settings.
E-13
x Signal reception may not be possible at the distances noted below during certain times of the year or
day. Radio interference may also cause problems with reception.
− Mainfl ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)
− Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
− Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
− Shangqiu (China) transmitter: 500 kilometers (310 miles)
x As of June 2013, China does not use Daylight Saving Time (DST). If China does go to the Daylight
Saving Time system in the future, some functions of this watch may no longer operate correctly.
x Using this watch in a country covered by a time calibration signal that is different from the countries it
supports may result in incorrect time indication due to local application of summer time, etc.
To get ready for a receive operation
1. Place the watch in a location where signal reception is good.
12 o’clock
or
x Position the watch as shown in the nearby illustration,
with 12 o’clock pointed towards a window. Make sure
there are no metal objects nearby.
x Signal reception normally is better at night.
x The receive operation takes from two to seven minutes,
but in some cases it can take as long as 14 minutes.
Take care that you do not perform any button operation
or move the watch during this time.
E-12
Approximate Reception Ranges
Japanese Signals Chinese Signal
Fukushima
500 kilometers
1,000 kilometers
Fukuoka/Saga
1,500 kilometers
Changchun500 kilometers
Beijing
Shangqiu
Shanghai
Chengdu
Hong Kong
UK and German Signals North American Signal
Anthorn
500 kilometers
1,500 kilometers
Mainfl ingen
The Anthorn signal is receivable
within this area.
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
Fort Collins
E-11
Radio Controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly. However, when
using the watch outside of areas covered by time calibration signals, you will have to adjust the settings
manually as required. See “Confi guring Current Time and Date Settings Manually” (page E-23) for more
information.
This section explains how the watch updates its time settings when the city code selected as the Home
City is in Japan, North America, Europe, or China, and is one that supports time calibration signal
reception.
If your Home City Code setting is this:
The watch can receive the signal from the transmitter
located here:
LONDON (LON), PARIS (PAR), ATHENS (ATH) Anthorn (England), Mainfl ingen (Germany)
HONG KONG (HKG) Shangqiu City (China)
TOKYO (TYO) Fukushima (Japan), Fukuoka/Saga (Japan)
NEW YORK (NYC), CHICAGO (CHI),
DENVER (DEN), LOS ANGELES (LAX),
ANCHORAGE (ANC), HONOLULU (HNL)
Fort Collins, Colorado (United States)
Important!
x The areas covered by HONOLULU (HNL) and ANCHORAGE (ANC) are quite far from the calibration
signal transmitters, so certain conditions may cause reception problems.
E-10
Power Saving
Power Saving enters a sleep state automatically whenever the watch is left for a certain period in an area
where it is dark. The table below shows how watch functions are affected by Power Saving.
x There actually are two sleep state levels: “second hand sleep” and “function sleep”.
Elapsed Time in Dark Operation
60 to 70 minutes (second hand sleep)
2
2
Second Hand only stopped at 12 o’clock, all other functions enabled
6 or 7 days (function sleep)
x All functions, including timekeeping, disabled
x Internal timekeeping maintained
x The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch is already in a sleep
state when 6:00 AM arrives, however, it will remain in the sleep state.
To recover from the sleep state
Move the watch to a well-lit area or press any button.
E-9
Power Recovery Mode
The watch is designed to go into a power recovery mode that stops hand operation temporarily whenever
power suddenly drops below a certain level due to continuous signal reception or other operations over a
short period. Note that all operations are disabled while the watch is in the power recovery mode.
The hands will move to the correct positions and the watch will resume normal operation after power
recovers (in about 15 minutes). Putting the watch in a location where it is exposed to light will help power
to recover sooner.
Charging Times
Exposure Level (Brightness)
Daily
Operation *1
Level Change *2
Level 3 Level 2 Level 1
Outdoor sunlight (50,000 lux) 8 minutes 3 hours 30 hours
Window sunlight (10,000 lux) 30 minutes 7 hours 111 hours
Window sunlight on cloudy day (5,000 lux) 48 minutes 11 hours 178 hours
Indoor fl uorescent lighting (500 lux) 8 hours 120 hours – – –
* 1 Approximate exposure each day to generate power for normal daily operation.
* 2 Approximate exposure to take power up one level.
x The above times are for reference only. Actual times depend on lighting conditions.
x For details about the operating time and daily operating conditions, see the “Power Supply” section of
the Specifi cations (page E-34).
E-8
Important!
x Keep the watch in an area normally exposed to bright light when storing it for long periods. This helps
to ensure that power does not run down.
x Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is
blocked from exposure to light can cause power to run down. Make sure that the watch is exposed to
bright light whenever possible.
Power Levels
You can get an idea of the watch’s power level by observing the movement of
the
2
Second Hand.
x If the
2
Second Hand is moving normally at one-second intervals, power is
at Level 1.
x If the
2
Second Hand is moving at two-second intervals, power is at Level 2,
which is quite low. Expose the watch to light as soon as possible so it can
charge (Low battery alert).
Level Hand Movement Function Status
1 Normal. All functions enabled
2
2
2
Second Hand moves at two-second intervals.
4
4
Day Indicator changes to 1 (home position).
Time calibration signal
reception disabled
3
2
2
Second Hand stopped.
1
1
Hour Hand and 3
3
Minute Hand stopped at
12 o’clock.
All functions disabled
x When power drops to Level 3, all settings (including timekeeping) will be cleared. Recharging the
battery will reset all settings to their initial factory defaults.
Moves at two-second
intervals.
1
4
2
31