Casio 5235 Watch User Manual


 
Operation Guide 5235 (OC)
E-31
The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is possible, see “To
x
confi gure Home City settings” (page E-19).
The period when summer time is applied in the location where you are using the watch may be x
different from the period set for your currently selected Home City. Use the procedure under “To switch
between standard time and summer time manually” (E-21) to switch from AUTO to STD (for standard
time) or DST (for summer time).
The hands and/or day indicator is off.
This could indicate that the watch has been exposed to magnetism or strong impact, which has caused
problems with proper hand and day indicator alignment. Adjust the watch’s hand and day indicator home
position alignment (page E-27).
Charging
The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3 (page E-8). Continue exposing the watch to light
until the
x
Second Hand starts moving normally (at one-second intervals).
The
x
Second Hand starts to move at one-second intervals, but then suddenly returns to moving
at two-second intervals.
The watch probably is not suffi ciently charged yet. Continue keeping it exposed to light.
E-30
Troubleshooting
Hand Movement and Position
The
x
Second Hand is moving at two-second intervals.
All the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the
x
Second Hand starts moving normally, at one-
second intervals (page E-8).
The hands of the watch suddenly start moving at high speed, even when I do not perform any
operation.
This could be due to any one of the following causes. In all cases, the hand movement does not indicate
malfunction, and should stop shortly.
The watch is recovering from a sleep state (page E-10).
x
The time setting is being adjusted following a successful auto time calibration signal receive operation x
(page E-11).
Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-9). Do not perform any operation until the hands
return to their normal positions (in about 15 minutes). The hands should return to their correct positions
when normal operation returns. To help power recover, leave the watch in a location where it is exposed
to light.
The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it, if necessary (page
x
E-19).
E-29
Press 3. B.
This enters the x
v
Day Indicator home position adjustment mode.
Check the 4.
v
Day Indicator to confi rm that it is 1, which is its home position.
If the x 1 is not in the center of the
v
Day Indicator, rotate the crown to
center it.
Rotating the crown three full consecutive turns clockwise will cause the
x
v
Day Indicator to start changing in a forward direction (increment).
To stop x
v
Day Indicator movement, press any button.
Push the crown back in to return to regular timekeeping.5.
This will cause the hands to return to their normal positions and resume
x
regular timekeeping. Wait until everything stops moving before performing
any other operation.
>
E-28
To adjust home positions manually
Pull out the crown.1.
Hold down 2. B until the
x
Second Hand completes the two-part movement
described below. Note that you will need to keep B depressed for at least
seven seconds.
Part 1:
x About two seconds after you fi rst hold down B, the
x
Second
Hand should move to 57-second or 3-second position, if the
x
x Second Hand is adjusted correctly.
If the
x
Second Hand does not move to 57-second or 3-second position,
it means that its home position is off and needs adjustment.
Part 2:
x Next, the
x
Second Hand will move to 12 o’clock.
After the
x
Second Hand moves to 12 o’clock, release B. When you
do, home position adjustment of all of the hands (but not the
v
Day
Indicator) will start automatically.
Home position adjustment is complete when all hands are at 12 o’clock.
To exit the home position adjustment operation and return to regular
timekeeping, push the crown back in.

>
@
E-27
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or day setting to be off, even if the watch is able to
perform the signal receive operation.
Auto Home Position Adjustment
Auto correction of hand home positions corrects the hand position automatically.
Auto correction corrects the positions of all hands. For the
x
v
Day Indicator, you must perform the
manual adjustment procedure under “To adjust home positions manually” (page E-28).
Manual Home Position Adjustment
Perform the procedure in this section if auto home position adjustment is not possible for some reason.
Hand home position adjustment is not required if the time and day settings are correct. x
Note
Any time after you enter the home position adjustment mode in step 1 of the following procedure, you
x
can return to regular timekeeping by pushing the crown back in. In this case, any adjustments you
made before the watch returned to regular timekeeping will be applied.
If you do not perform any operation with the crown for about two minutes after pulling it out, crown
x
operations will become disabled and hands will not move if you rotate the crown. If this happens, push
the crown back in and then pull it out again.
E-26
Press 7. B. This will enter the year setting mode.
The x
z
Hour Hand will move to the number that represents the
tens digit of the year and the
c
Minute Hand will move to the
number that represents the ones digit. The
x
Second Hand will
move to 12 o’clock and stop there.
Rotate the crown to adjust the year setting.8.
If you want to change the time setting at this time, press
x B and
then perform the procedure starting from step 4 under “To change
the current time setting manually” (page E-23).
After the settings are the way you want, push the crown back in to 9.
return to regular timekeeping.
This causes timekeeping to resume with the
x
x
Second Hand
starting from 12 o’clock.
Note
The watch’s built-in full automatic calendar makes allowances for x
different month lengths and leap years. Once you set the date, there
should be no reason to change it except after you have the watch’s
rechargeable battery replaced or after power drops to Level 3.
+
Setting the year (ones digit)
0
1
2
3
4
9
8
6
57
B
Setting the year (tens digit)
00
10
20
30
40
90
80
60
5070
E-25
To change the current date setting manually
Pull out the crown.1.
This will cause the
x
x
Second Hand to move to the city code of
the currently selected Home City.
Hold down 2. B for about two seconds.
The
x
x
Second Hand will indicate whether the current time is
a.m. (by moving to second 57) or p.m. (by moving to second
03).
Press 3. B twice. This will enter the date setting mode.
The
x
v
Day Indicator will move slightly to indicate the setting
mode.
Rotate the crown to adjust the date setting.4.
After the 5.
v
Day Indicator stops moving, press B. This will enter
the month setting mode.
The
x
x
Second Hand will move to the currently selected month.
Rotate the crown to adjust the month setting.6.
@
Dec
Nov
Feb
Mar
Apr
Oct
Sep
Aug
Jan
Jul May
Jun
Setting the month

>
@
E-24
Home City/DST
Hour/Minute Hour
Year DayMonth
B
BB
B
BB
Rotate the crown to adjust the time (hour and minute) setting.4.
Rotating the crown three full consecutive turns clockwise will cause the
x
c
Minute Hand to start
moving clockwise. Rotating the crown another three full consecutive turns clockwise will cause the
c
Minute Hand to start moving at high speed. To stop hand movement, press any button or rotate
the crown one full turn counterclockwise.
When adjusting the setting, check to make sure that the
x
x
Second Hand correctly indicates an a.m.
time or p.m. time.
If you want to change the date setting at this time, press
x B and perform the procedure starting from
step 3 under “To change the current date setting manually” (page E-25).
After the settings are the way you want, push the crown back in to return to regular timekeeping.5.
This causes timekeeping to resume with the
x
x
Second Hand starting from 12 o’clock.