Filter
Top Products
Operation Guide 5216
E-29
While a setting is fl ashing, use 4. D (+) and B (–) to change it.
When setting the alarm time using the 12-hour format, take care to set the time x
correctly as a.m. (no indicator) or p.m. (P indicator).
Press 5. A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode
the watch is in.
Alarm and Hourly Time Signal operations are performed in accordance with the x
Timekeeping Mode digital time.
To stop the alarm tone after it starts to sound, press any button. x
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-28
To set an alarm time
In the Alarm Mode, use 1. D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
D D
D D
D D
To set a one-time alarm, display one of the screens indicated by an alarm number x
from
through .
After you select an alarm, hold down 2. A until the hour setting of the alarm time
starts to fl ash, which indicates the setting screen.
This operation automatically turns on the alarm. x
Press 3. C to move the fl ashing between the hour and minute settings.
E-27
Alarms
You can set fi ve independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
There are six screens in the Alarm Mode. Five are for x
one-time alarms (indicated by numbers from
through
), and one is for the Hourly Time Signal (indicated
by
).
All of the operations in this section are performed in the x
Alarm Mode, which you enter by pressing C (page E-7).
!LARMTIME
(OUR-INUTES
!LARMNUMBER
/N/FFSTATUS
E-26
Use 2. B and D to change the countdown start time as described below.
Screen Button Operation
Use D (+) and B (–) to change the setting.
You can set a start time in the range of 1 to 60 minutes in 1-minute increments. x
Press 3. A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
The countdown timer operation continues even if you exit x
the Countdown Timer Mode.
Press x D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
To completely stop a countdown operation, fi rst pause x
it (by pressing D), and then press A. This returns the
countdown time to its starting value.
E-25
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero by
beeping for about 10 seconds or until you stop it by pressing any button.
To confi gure the countdown timer
While the countdown start time is on the display in the 1.
Countdown Timer Mode, hold down A until the current
countdown start time starts to fl ash, which indicates the
setting screen.
If the countdown start time is not displayed, use the x
procedure under “To use the countdown timer” (page
E-26) to display it.
E-24
Countdown Timer
-INUTES
3ECONDS
The countdown timer can be set within a range of
one minute to 60 minutes. An alarm sounds when the
countdown reaches zero.
All of the operations in this section are performed in the x
Countdown Timer Mode, which you enter by pressing C
(page E-7).
Confi guring the Countdown Timer
You need to set a countdown start time before actually
using the countdown timer.
See “To confi gure the countdown timer” on page E-25 for x
information about setting up the timer.
E-23
To measure times with the stopwatch
Elapsed Time
D D D D A
Start Stop Re-start Stop Clear
E-22
Stopwatch
The stopwatch lets you measure elapsed time.
The display range of the stopwatch is 59 minutes, 59.99 x
seconds.
The stopwatch continues to run, restarting from zero after x
it reaches its limit, until you stop it.
The stopwatch measurement operation continues even if x
you exit the Stopwatch Mode.
All of the operations in this section are performed in the x
Stopwatch Mode, which you enter by pressing C (page
E-7).
-INUTES
3ECONDS
SECOND
E-21
To toggle a city code time between Standard Time and Daylight Saving Time
$34INDICATOR
In the World Time Mode, use 1. D to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
Hold down 2. A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
The DST indicator is on the display whenever you display x
a city code for which Daylight Saving Time is turned on.
Note that the DST/Standard Time setting affects only x
the currently displayed city code. Other city codes are
not affected.
Note that you cannot switch between Standard Time x
and Daylight Saving Time while
is selected as the
city code.
E-20
To view the time in another city
In the World Time Mode, press D.
This will cause the city code of the currently selected World Time City to appear for x
about two seconds, followed by the current time in that city.
Pressing x D while a city code is displayed will scroll to the next city code, in the
sequence noted in the “City Code Table” at the back of this manual.
If the current time shown for a city is wrong, it probably means there is a problem x
with your Timekeeping Mode time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary adjustments.