Filter
Top Products
Operation Guide 5113 5213
E-64
1 second
Record name
Month
Day
1 second
Hour : Minutes
Altitude
Altitude
High altitude
Low altitude
1 second
1 second
1 second
Cumulative ascent
Cumulative recording
start month and day
1 second
Cumulative descent
Cumulative recording
start month and day
Manual Save 1 Manual Save 14 High Altitude (HI)
Cumulative Ascent (ASC) Low Altitude (LO)Cumulative Descent (DSC)
E-65
3. After you are fi nished viewing data, use
D
to exit the Data Recall Mode.
•
- . - -
will be displayed if data has been deleted or if there is no corresponding data due to error, etc.
In such cases, cumulative ascent ( ASC ) and cumulative descent ( DSC ) values will show zero.
• When the cumulative ascent ( ASC ) or cumulative descent ( DSC ) exceeds 99,995 meters (or 327,980
feet), the applicable value will restart from zero.
To delete a single altitude record
1. In the Data Recall Mode, use
A
and
C
to scroll through records until the one you want to delete is
displayed.
2. Hold down
E
for about two seconds until each of the following steps occurs.
• Hold CLR appears on the digital display. ➝ CLR appears.
• This deletes the record you displayed in step 1.
• Release
E
after CLR appears on the digital display.
• Deleting a manual save record shifts all of the records following it up one position.
To delete all altitude records
In the Data Recall Mode, hold down
E
for about fi ve seconds until each of the following steps occurs.
•
Hold CLR
appears on the digital display.
➝
CLR
appears.
➝
Hold ALL
appears.
➝
CLR ALL
appears.
• This deletes all of the records currently in memory.
E-66
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use
D
to select the Stopwatch Mode (
ST
) as shown on page E-16.
• About one second after
ST
appears on the digital display, the display
will change to show the stopwatch time.
To perform an elapsed time operation
A
A
A A
C
Start Stop (Restart) (Stop) Reset
To pause at a split time
A
C
C A
C
Start Split
(
SPL
displayed)
Split release Stop Reset
Seconds
1/100
second
Minutes
Seconds
1/100
second
Minutes
E-67
To measure two fi nishes
A
C
A C
C
Start Split
First runner fi nishes.
Display time of fi rst
runner
Stop
Second runner
fi nishes.
Split release
Display time of
second runner
Reset
Note
• The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59.99 seconds.
• Once started, stopwatch timing continues until you press
C
to stop it, even if you exit the Stopwatch
Mode to another mode and even if timing reaches the stopwatch limit defi ned above.
• Exiting the Stopwatch Mode while a split time is frozen on the digital display clears the split time and
returns to elapsed time measurement.
E-68
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time, and sound an alarm when the end of the
countdown is reached.
To enter the Countdown Timer Mode
Use
D
to select the Countdown Timer Mode (
TR
) as shown on page E-16.
• About one second after
TR
appears on the digital display, the display
will change to show the current countdown start time.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting
down), press
A
to stop it and then press
C
to reset to the current
countdown start time.
• If a countdown is paused, press
C
to reset to the current
countdown start time.
2. Hold down
E
until each of the following steps occurs.
• Hold SET appears on the digital display. ➝ The current countdown
start time fl ashes.
3. Use
A
(+) and
C
(–) to change the minute setting.
4. Press
E
to exit the setting screen.
Countdown time
(Minutes, seconds)
Countdown time
(Minutes, seconds)
E-69
To perform a countdown timer operation
A
A
A A
C
Start Stop (Restart) (Stop) Reset
• Before starting a countdown timer operation, check to make sure that a countdown operation is not in
progress (indicated by the seconds counting down). If it is, press
A
to stop it and then
C
to reset to
the countdown start time.
• An alarm sounds for fi ve seconds when the end of the countdown is reached. This alarm will sound in
all modes. The countdown time is reset to its starting value automatically when the alarm sounds.
To stop the alarm
Press any button.
E-70
Using the Alarm
You can set fi ve independent daily alarms. When a daily alarm is turned
on, an alarm tone will sound for about 10 seconds each day when the
time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
You can also turn on an Hourly Time Signal, which will cause the watch
to beep twice every hour on the hour.
To enter the Alarm Mode
Use
D
to select the Alarm Mode (
AL
) as shown on page E-16.
• About one second after
AL
appears on the digital display, the display
will change to show an alarm number (
−1
through
−5
) or the
indicator. The alarm number indicates an alarm screen. is shown
when the Hourly Time Signal screen is on the digital display.
• When you enter the Alarm Mode, the data you were viewing when you
last exited the mode appears fi rst.
Alarm time
(Hour: Minutes)
Alarm
number
Alarm time
(Hour: Minutes)
Alarm
number
E-71
To set an alarm time
1. In the Alarm Mode, use
A
and
C
to scroll through the alarm (
–1
through
–5
) until the one whose time you want to set is displayed.
−1 −2 −3
−5
−4
2. Hold down
E
until each of the following steps occurs.
• Hold SET appears on the digital display. ➝ The current setting
fl a s h e s.
• This is the setting screen.
3. Press
D
to move the fl ashing between the hour and minute settings.
4. While a setting is fl ashing, use
A
(+) and
C
(–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no
indicator) or p.m. ( P indicator).
5. Press
E
to exit the setting screen.
Alarm ON/OFF
indicator
Alarm ON/OFF
indicator