Filter
Top Products
Operation Guide 5178
E-40
• The watch will adjust the DST setting automatically when it receives a time
calibration signal while any one of the following city codes is selected as the
Home City.
LON, PAR, ATH, TYO, ANC, LAX, DEN, CHI, NYC
• The watch will not adjust the DST setting automatically while either of following
city codes is selected as the Home City. In this case, you will need to change
between standard time and daylight saving time manually.
HKG, HNL
• If you want to proceed with adjusting the current time and date setting, continue
from step 3 under “Configuring Time and Date Settings Manually” (page E-41). If
you do go the date and time adjustment procedure, note that you will not be able
to return to this Home City and daylight saving time setting procedure. To return to
this procedure, you will need to press A to exit the time and date setting
procedure, and then perform this procedure from step 1, above.
5. When everything is the way you want, press A.
• This will apply your settings and return to normal timekeeping. The second hand will
move to and start timekeeping from the appropriate seconds count in accordance
with the watch’s internal timekeeping.
E-41
Configuring Time and Date Settings Manually
You can use the following procedures to adjust the time and date settings when the
watch is unable to receive a time calibration signal for some reason.
1. In the Timekeeping Mode, keep A depressed (for about five seconds) as the
second hand moves to the last signal reception result (“Y” or “N”), then to “READY”
(or “R” for some models), and then to the city code of the currently selected Home
City.
2. Use C to cycle through available settings in the sequence shown below.
C
• Home City
• DST setting
Hour and
minute
C
Year
C
C
Month
C
Day
E-42
3.Press C.
• The second hand will move to 12 o’clock, and the left
dial hand will move to “0” (“60” for some models).
4.Use D (+) and B (–) to change the time setting in
one-minute increments.
• Check the bottom dial hand to make sure that it is
indicating the correct 24-hour setting.
5.Press C to advance to the year setting.
• The year setting consists of a tens digit and a units
digit setting.
30
30
Units digit
Tens digit
Second hand
E-43
6.Use D (units digit) and B (tens digit) to change the
year setting.
• D: Increases the one’s digit by 1.
• B: Increases the tens digit by 10.
7.Press C to advance to the month setting.
0
1
2
3
4
5
6
7
8
9
00
50
1090
2080
3070
40
60
Second
hand
Left dial hand
E-44
30
8.Press D to move to the next month.
9.Press C to advance to the day setting.
10. Use D (+) and B (–) to change the day setting.
11. When everything is the way you want, press A.
• This will exit the setting procedure and reset the
seconds count to zero.
• Press A to restart timekeeping on a time signal on the
TV or radio.
• The day of the week is calculated automatically.
DEC
JUN
JAN
FEB
MAR
APR
MAY
NOV
OCT
SEP
AUG
JUL
Second hand
E-45
Auto Hand Home Position Correction
Strong magnetism or impact can cause the hands and/or day setting to be off, even if
the watch is able to perform the signal receive operation. Auto hand home position
correction corrects the hand position automatically.
• Auto correction is performed in the Timekeeping Mode only.
• The auto correction operation corrects the positions of the second, minute, and hour
hands. Home position correction of the dial hands and day must be performed
manually, using the procedure under “Manual Home Position Correction” (page
E-48).
• Each hour, the watch performs automatic correction of the hand positions.
Correction can be performed for error up to 55 minutes slow or 5 minutes fast.
• You also can trigger the auto hand home position correction operation manually, if
you want. See “To trigger the auto hand home position correction operation
manually” (page E-46) for more information.
• The auto hand home position correction operation can take up to three and a half
minutes to complete.
E-46
• If hand positions are off by one hour or more, correct them using the procedure
under “To trigger the auto hand home position correction operation manually” (page
E-46) or “Manual Home Position Correction” (page E-48).
To trigger the auto hand home position correction operation manually
• Perform the following procedure when the time setting is
off.
In the Timekeeping Mode, hold down D for about six
seconds until the second hand completes one full
revolution.
• Though the second hand will stop momentarily about
three seconds after you hold down D, do not release
the button yet. Wait until the second hand completes a
full revolution before you release D.
• To interrupt an ongoing correction operation and return
to the Timekeeping Mode, press D again.
30
E-47
• If you release D when the second hand stops the first time (after about three
seconds) in the above operation, the watch will enter the manual home position
correction mode, which is described under “Manual Home Position Correction” (page
E-48). If this happens, press A to return to the Timekeeping Mode and then perform
the above operation again.
The manually triggered auto home position correction operation performs the following
two steps.
1. The hands will move automatically in order to determine the home positions of the
watch.
2. After the hand home positions are determined, the watch will return to normal
timekeeping automatically. This completes the correction operation.
E-48
Manual Home Position Correction
Strong magnetism or impact can cause the hands and/or day setting to be off, even if
the watch is able to perform the signal receive operation. If this happens, perform the
following home position correction procedure.
• Hand home position correction is not required if the time and day settings are
correct.
• You also can use auto hand home position correction (page E-45) to correct the
home positions of the second, minute, and hour hands.
1.In the Timekeeping Mode, hold down D for about three
seconds until the second hand stops. Release D at
this time.
30
Second hand
E-49
• Each press of C cycles through available settings in the sequence shown below.
C
Second
hand
Hour and minute
hands, bottom
dial hand
C
Right dial hands
(24-hour hour and
minute)
C
C
Left dial hand
(day of the
week)
C
Day
2. Check the second hand position.
• Home Position
Second hand: 12 o’clock
3. If the second hand home position is off, use D to move it clockwise to correct it.