Filter
Top Products
Operation Guide 5098/5099/5101
E-39
Use 5. C (+) and B (–) to adjust the
n
Minute Hand (elapsed time) so it is at its
home position (0).
Holding down either button for about two seconds and then releasing it starts
x
high-speed hand movement in the applicable direction.
To stop high-speed hand movement, press any button.
x
After adjusting the home position, go to step 6. x
Press 6. A to exit home position correction and return to regular timekeeping.
E-38
Press 4. A. This will cause the
n
Minute Hand (elapsed time) to move to its home
position (0).
If the
x
n
Minute Hand (elapsed time) is at the correct home position, advance to
step 6.
6 6
<Module 5098>
<Modules 5099 and 5101>
E-37
If the current home positions are greater than ±15 minutes 00 seconds
2. After performing step 1, hold down C and B at the
same time until the
z
Hour Hand,
c
Minute Hand,
x
Second Hand, and
v
24-hour Hand all move to 12
o’clock.
Use 3. C (+1 second) and B (–1 second) to adjust the
hand positions so they point to 12 o’clock.
Holding down either button for about two seconds
x
and then releasing it starts high-speed hand
movement in the applicable direction.
To stop high-speed hand movement, press any
x
button.
The x
v
24-hour Hand is synchronized with the
z
Hour Hand and
c
Minute Hand, so separate
adjustment is not required.
After adjusting the home positions, go to step 4.
x
B +@
>
<Modules 5099 and 5101>
<Module 5098>
E-36
If the current home positions are within ±15 minutes 00 seconds
Use 2. C (+1 second) and B (–1 second) to adjust the
hand positions so they point to 12 o’clock.
Holding down either button for about two seconds and
x
then releasing it starts high-speed hand movement in
the applicable direction.
To stop high-speed hand movement, press any
x
button.
After adjusting the home positions, go to step 4. x
+@
E-35
In the regular timekeeping, hold down 1. A for about 10
seconds until the
c
Minute Hand and
x
Second Hand
move to 12 o’clock.
The
x
x
Second Hand goes through the sequence
described below.
Last signal reception result o RC o Current location
setting o Keep A depressed until the
x
Second
Hand starts to move counterclockwise. You can
release A at this time.
The
x
c
Minute Hand and
x
Second Hand are in their
correct home positions if they are pointed precisely
at 12 o’clock. If the hands are in the correct home
positions, advance to step 4.
+
@
E-34
Hand Home Position Adjustment
If the time setting of your watch is not correct even though time calibration signal
reception is being performed normally, use the procedure in this section to check the
home positions of the hands and make adjustments as required.
Note that you do not need to perform the following operation if your watch is showing
the correct time.
Important!
It can take up to 14 minutes for the hands to move to their home positions for hand
x
home position adjustment. It also can take up to 14 minutes for the hand to return to
their normal positions following hand home position adjustment.
When performing the following procedure, it is recommended that after you move to
x
a home position, you press B to move the setting back one step. Next, press C to
return it to the home position. This helps to ensure better home position adjustment
accuracy.
E-33
To perform an elapsed time operation
B
B B B C
Start Stop (Restart) (Stop) Reset
Note
Check the current position of the
x
n
Minute Hand (elapsed time). If it is pointed at 5,
for example, it means that fi ve minutes have elapsed.
The minute counter can indicate elapsed time up to 20 minutes.
x
The x
b
Ornament moves with each second, making one revolution per minute
(60 seconds).
While the minute counter hands are stopped (not moving), press
x C to reset the
n
Minute Hand (elapsed time) to 0.
E-32
Using the Minute Counter
The minute counter measures elapsed time.
Hand Functions
b
Ornament
n
Minute Hand (elapsed time)
<Modules 5099 and 5101>
6*
<Module 5098>
6*
E-31
After the setting is the way you want, press 5. A.
This will exit the setting mode and the
x
x
Second Hand will resume regular
timekeeping.
For best timekeeping accuracy, press
x A on a time signal from the TV or radio.
The watch will exit the setting mode automatically if you do not perform any x
button operation for about two or three minutes.
E-30
Use 4. C (+1 minute) and B (–1 minute) to change the
current time setting.
Holding down either button for about two seconds
x
and then releasing it starts high-speed hand
movement in the applicable direction.
Pressing
x C and B at the same time will start high-
speed hand movement, which will continue until the
hands complete a 24-hour rotation.
To stop high-speed hand movement, press any
x
button.
Check the x
v
24-hour Hand to make sure that the time
is set properly (1:00 a.m. = 1 o’clock,
1:00 p.m. = 13 o’clock).
<Modules 5099 and 5101>
>
<Module 5098>