Filter
Top Products
Operation Guide 5073
3
To select a mode
Starting from the regular timekeeping mode, press C to toggle between the regular
timekeeping mode and the World Time setting mode. You can tell what mode is
currently selected by checking the v Day of the Week Hand, as described below.
Regular timekeeping mode
The hand indicates the day of the
week (Su, Mo, Tu, We, Th, Fr, Sa).
World Time setting mode
In the World Time setting mode, the
short end of the hand indicates whether
the time for the currently selected
World Time City is standard time (STD)
or daylight saving/summer time (DST).
> >
Timekeeping
Hand Functions
Regular timekeeping
z Hour Hand
x Second Hand
c Minute Hand
v Day of the Week Hand
b Day
World Time
n World Time Hour Hand: Indicates the current time in
the World Time City in 24-hour
format.
m World Time Minute Hand
To return to regular timekeeping from any other mode or function, hold down • C for
about two seconds.
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
Note
This watch does not have a city code that corresponds •
to Newfoundland.
In the regular timekeeping mode, keep 1. A depressed
(for about five seconds) as the
x Second Hand goes
through the following sequence.
Moves to the last signal reception result ( • Y or N), then
to READY (or R for some models), and then to the city
code of the currently selected Home City.
This is the city code setting mode. •
The watch will exit the setting mode automatically if •
you do not perform any operation for about two or
three minutes.
For details about city codes, see the “City Code •
Table”.
To change the Home City setting, press 2. D to move the
x Second Hand clockwise.
Keep pressing • D until the
x Second Hand is pointing
at the city code you want to select as your Home City.
Each time you change the city code setting, the •
z
Hour Hand,
c Minute Hand and b Day move to
the current time and date for that city code. Do not
perform the next operation until these hands stop
moving.
Press 3. B to toggle the time for the currently selected city code between STD
(standard time)/DST (daylight saving time).
While you are selecting the Home City code, the short end of the •
v Day of the
Week Hand will indicate whether the currently selected city code is configured
for standard time (STD) or daylight saving/summer time (DST).
Note that you cannot switch between • STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
After all the settings are the way you want, press 4. A to return to regular
timekeeping.
To toggle the Home City time between standard time and daylight saving time
Perform the step 1 under “To configure Home City settings”.1.
Each time you select a city code, the •
z Hour Hand and c Minute Hand move to
the current time for that city code. Do not perform the next operation until these
hands stop moving.
The short end of the •
v Day of the Week Hand will indicate whether the currently
selected city code is configured for standard time (STD) or daylight saving/
summer time (DST).
Press 2. B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
Note that you cannot switch between • STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
After all the settings are the way you want, press 3. A to return to regular
timekeeping.
B +@
56 *>
@
B +
>@ *
Note
After you specify a city code, the watch will use UTC* offsets to calculate the •
World Time based on the current time in your Home City.
Coordinated Universal Time, the world-wide scientific standard of timekeeping. *
The reference point for UTC is Greenwich, England.
Selecting some city codes automatically makes it possible for the watch to •
receive the time calibration signal for the corresponding area. See “Radio
Controlled Atomic Timekeeping” for details.
Configuring Current Time and Date Settings Manually
You can configure current time and date settings manually when the watch is unable
to receive a time calibration signal.
To change the current time setting manually
In the regular timekeeping mode, keep 1. A depressed
(for about five seconds) as the
x Second Hand goes
through the following sequence.
Moves to the last signal reception result ( • Y or N), then
to READY (or R for some models), and then to the city
code of the currently selected Home City.
The short end of the •
v Day of the Week Hand will
indicate whether the currently selected city code is
configured for standard time (STD) or daylight saving/
summer time (DST).
Change the Home City and daylight saving time (DST) 2.
settings, if you want.
For details about these settings, see steps 2 and 3 •
under “To configure Home City settings”.
In the following steps, each press of • C cycles
between settings as shown below.
Home city/DST Hour/Minute
Year
(tens digit)
Day Month
Year
(ones digit)
Press 3. C.
The •
v Day of the Week Hand will move to Su. This is the time setting mode.
The •
x Second Hand indicates whether the current time is a.m. (A) or p.m. (P).
Use 4. D (+) and B (–) to change the time (hour and minute) setting.
Each press of either button will move the hands ( •
z Hour Hand and c Minute
Hand) to one minute.
Holding down • D or B will start high-speed
z Hour Hand and c Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
When setting the time, make sure that the •
x Second Hand is in the correct
A (a.m.) or P (p.m.) position for the time you are setting.
If you want to change the date setting at this time, press • C and perform the
procedure starting from step 3 under “To change the current date setting
manually”.
After the time setting is the way you want, press 5. A to return to regular
timekeeping.
This will cause the •
x Second Hand to move automatically to 12 o’clock and
resume movement from there.
To change the current date setting manually
@
00
50
10
40
20
3090
60
80
70
Setting the year (tens digit)
In the regular timekeeping mode, keep 1. A
depressed (for about five seconds) as the
x Second Hand goes through the following
sequence.
Moves to the last signal reception result ( • Y or
N), then to READY (or R for some models),
and then to the city code of the currently
selected Home City.
Press 2. C twice.
The •
x Second Hand will move to the tens digit
of the current year setting. This is the year
setting mode.
The year can be set in the range of 2000 to •
2099.
Press 3. D to move the
x Second Hand clockwise
until it is pointing at the year tens digit you want
to select.
@
0
5
1
4
2
39
6
8
7
Setting the year (ones digit)
After you select the year tens digit, press 4. C.
The • x Second Hand will move to the ones digit
of the current year.
Press 5. D to move the
x Second Hand clockwise
until it is pointing at the year ones digit you want
to select.
After you select the year ones digit, press 6. C.
The •
x Second Hand will move to the currently
selected month. This is the month setting
mode.
@ >
B +
@ >