Filter
Top Products
Operation Guide 5022
1
MO0804-EA
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
••
••
• This watch does not have a city code that corresponds to the Greenwich
Mean Time differential of –3.5 hours. Because of this, the radio-controlled
atomic timekeeping function will not display the correct time for
Newfoundland, Canada.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the watch is
stored by a built-in battery. Leaving or using the watch
where it is not exposed to light causes the battery to run
down. Make sure the watch is exposed to light as much as
possible.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
• You should try to keep the watch outside of your sleeve
as much as possible. Even if the face of the watch is
blocked only partially from light, charging will be reduced
significantly.
l
l
l
l
l
l
l
l
l
l
l
Bright light
Solar cell
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light. Battery discharges in the dark.
Bright light
Electrical
energy
All
functions
enabled.
LEVEL 1
LEVEL 2
Charge
Solar cell
(Converts light to
electrical power.)
Rechargeable battery
LEVEL 1
LEVEL 2
Some
functions
disabled.
Dis-
charge
• The actual level at which some functions are disabled depends on the watch model.
• Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
If the analog hands aren’t moving...
If the analog hands aren’t moving, it means that the power saving mode has stopped
them to save battery power.
• See “Power Saving” for more information.
• The hands also stop when the watch’s battery runs down.
About This Manual
• Depending on your watch’s model number, the printing on its face will look like that
shown either in Figure A or Figure B. All of the illustrations in this manual use the
face shown in Figure A.
30
Day of the
week hand
Stopwatch
second hand
Minute
hand
Hour hand
Date
Second hand
24-hour
hand
Figure BFigure A
30
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need in order to
perform operations in each mode. Further details and technical information can be
found in the “Reference” section.
General Guide
Manual Receive
30
Transmitter Change
Time/Date Adjustment
30
Receive Status Check
Timekeeping Mode
30
30
Press any button.
Hold down A for
about two seconds.
Hold down A
for about five seconds.
Press A.
▲
▲
Press A.
▲
▲
▲
▲
30 30
30
30
30
World Time Mode
Alarm Mode
Countdown Timer Mode
Timekeeping Mode
Stopwatch Mode
Press C.
Press C.
Press B or D.
Press D.
(When the stopwatch is
reset to all zeros.)
Press C.
▲
▲
▲
Press C.
▲
▲
▲
• Whenever you enter the Timekeeping, Countdown Timer, World Time, or Alarm
Mode, the hands of the watch move to the applicable time for that mode. Even if the
hands are moving, you can press C to move to another mode (except for the
Stopwatch Mode), if you want. Note, however, that all other buttons are disabled
while the hands are moving.
Radio-controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly.
• Supported time calibration signals: Germany (Mainflingen), England (Anthorn),
United States (Fort Collins), Japan (Fukushima or Fukuoka/Saga).
• See the information under “Signal Reception Troubleshooting” if you experience
problems with time calibration signal reception.
Current Time Setting
This watch adjusts its time setting automatically in accordance with a time calibration
signal. You also can perform a manual procedure to set the time and date, when
necessary.
• The first thing you should do after purchasing this watch is to specify your
Home City, which is the city where you normally will use the watch. For more
information, see “To specify your Home City”.
• When using the watch outside the areas covered by the time signal transmitters, you
will have to adjust the current time setting manually as required. See “Timekeeping”
for more information about manual time settings.
• The U.S. time calibration signal can be picked up by the watch while in North
America. The term “North America” in this manual refers to the area that consists of
Canada, the continental United States, and Mexico.
To specify your Home City
1. In the Timekeeping Mode, hold down A for about five
seconds until the watch beeps twice.
• The stopwatch second hand will move to the city code
of the currently selected Home City. This is the city
code setting mode.
• The second hand will stop at “0”.*
* Some models show “60” instead of “0”.
2.Use D to move the stopwatch second hand to the city
code you want to use as your Home City.
• Each press of D causes the stopwatch second hand
to advance clockwise to the next city code.
• Time calibration signal reception is supported when
any one of the city codes shown in the table below is
selected as your Home City.
• For full information on city codes, see the “City Code
Table”.
30
0
Stopwatch
second hand
City code
German/U.K. Signal Japan Signal U.S. Signal
City
Code
LON
PAR
ATH
City Name
London
Paris
Athens
City
Code
HNL
ANC
LAX
City Name
Honolulu
Anchorage
Los Angeles
City
Code
DEN
CHI
NYC
City Name
Denver
Chicago
New York
City
Code
HKG
TYO
City Name
Hong Kong
Tokyo
• In addition to the above, you also can select city codes that are outside the ranges
of the time calibration signal transmitters supported by this watch.
• Note that this watch does not have a city code that corresponds to Newfoundland.
3. After the Home City setting is the way you want, press A to return to the
Timekeeping Mode.
• Normally, your watch should show the correct time as soon as you specify your
Home City code. If it does not, it should adjust automatically after the next auto
receive operation. You also can perform manual receive or you can set the time
manually.
• Even if the time calibration signal is received correctly, there are some times when
the analog hands may not indicate the correct time. If this happens, use the
procedures under “Adjusting the Home Positions” to check the home positions of the
hands, and make adjustments as required.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signals transmitted from Mainflingen (Germany), Anthorn
(England), or Fort Collins (the United States) include both Standard Time and DST
data. When the Auto DST setting is turned on, the watch switches between Standard
Time and DST (summer time) automatically in accordance with the signals.
• Though the time calibration signal transmitted by the Fukushima and Fukuoka/Saga,
Japan transmitters include summer time data, summer time currently is not
implemented in Japan (as of 2007).
• The default DST setting is Auto DST (AT/AUTO) whenever you select LON, PAR,
ATH, ANC, LAX, DEN, CHI, NYC, or TYO as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it
probably is best to switch between Standard Time and Daylight Saving Time
(summer time) manually. For more information, see “To set the time and date
manually”.